Home | Contact Us | FAQ | Search & Site Map | Link to Us
Sign In | Join | Other 45 Sites in Network
HomeAnnouncements
Discussion Groups
By Brand
BMWChevroletDodgeFordGMHondaLexusMercedes-BenzNissanPeugeotToyotaVolkswagenOther Brands
By Topic
4x4 CarsRVsDrivingMaintenance & RepairCar AudioCollectible Cars
Country Specific
Australian ForumsUK Forums
ArticlesAuto InsuranceBuyingCars & TechnologyMaintenanceMiscellaneousSafety
DMV Resources
Related Topics
MotorcyclesBoatsMore Topics ...

Car Forum / Driving, Maintenance, Tuning / General Car Topics / January 2005

Tip: Looking for answers? Try searching our database.

It's Maddening!!!

Thread view: 
Enable EMail Alerts  Start New Thread
Thread rating: 
tranch728 - 06 Jan 2005 16:00 GMT
   Every time it either snows or we get a light rain and a freeze my doors
freeze shut. The locks are fine it's the doors that freeze shut and I can't
open them. I've been lucky, so far, and usually one door will open, and it's
usually a rear one so I have to crawl over the seats and console to get in,
start the car and let it run so it heats up. Once I get the heater going and
it warms up the doors defrost and open fine.

   Is there something I can do to, besides putting the car in a nice heated
garage, that will stop this?
Mark - 06 Jan 2005 16:11 GMT
Spray the rubber gaskets with silicone spray.
Mark

>    Every time it either snows or we get a light rain and a freeze my doors
> freeze shut. The locks are fine it's the doors that freeze shut and I
[quoted text clipped - 10 lines]
> heated
> garage, that will stop this?
MajorDomo@mailcity.com - 06 Jan 2005 16:47 GMT
A little silicone, sprayed on the rubber door moldings, works
fine

mike hunt

>     Every time it either snows or we get a light rain and a freeze my doors
> freeze shut. The locks are fine it's the doors that freeze shut and I can't
[quoted text clipped - 5 lines]
>     Is there something I can do to, besides putting the car in a nice heated
> garage, that will stop this?
tranch728 - 06 Jan 2005 20:06 GMT
> A little silicone, sprayed on the rubber door moldings, works
> fine
>
> mike hunt

   Thanks. I'll have to run out and get some today. Why is it the simplest
fixes are always the hardest to figure out yourself!?
sdlomi2 - 06 Jan 2005 20:13 GMT
> > A little silicone, sprayed on the rubber door moldings, works
> > fine
[quoted text clipped - 3 lines]
>     Thanks. I'll have to run out and get some today. Why is it the simplest
> fixes are always the hardest to figure out yourself!?

   That's why we ALL enjoy answering AND asking questions on these ng's.  I
for one have had my head 'under a hood' for ~50 years; but learn some mighty
'good stuff' on here. (Plus, silicone is much nicer to use than leaving your
door half-ajar!!!)  Good luck.  s
WEBPA - 07 Jan 2005 22:59 GMT
Careful!  You want "silicone spray lubricant"...NOT silicone gasket material,
silicone damping fluid, etc (there are many, many silicone-based solids and
liquids.)  I'd recommend you spray it on a cloth swatch or piece of sponge,
then rub in onto the weather seal; if you spray it directly, it could end up in
a bunch of places you don't want it.

>> > A little silicone, sprayed on the rubber door moldings, works
>> > fine
[quoted text clipped - 9 lines]
>'good stuff' on here. (Plus, silicone is much nicer to use than leaving your
>door half-ajar!!!)  Good luck.  s

webpa
tranch728 - 08 Jan 2005 01:50 GMT
> Careful!  You want "silicone spray lubricant"...NOT silicone gasket material,

   What a fun joke that'd be! Believe me. If I were THAT dumb, I'd deserve
to have my doors glued shut!!! :^)
WEBPA - 08 Jan 2005 18:49 GMT
No offense intended.

>> Careful!  You want "silicone spray lubricant"...NOT silicone gasket
>material,
>
>    What a fun joke that'd be! Believe me. If I were THAT dumb, I'd deserve
>to have my doors glued shut!!! :^)

webpa
tranch728 - 08 Jan 2005 21:21 GMT
   Oh, None taken. But I'll bet that somewhere, someone HAS to have that
explanation or they would glue their doors shut!

> No offense intended.
>
[quoted text clipped - 5 lines]
>
> webpa
Mark - 08 Jan 2005 21:40 GMT
I agree with that.
Mark

>    Oh, None taken. But I'll bet that somewhere, someone HAS to have that
> explanation or they would glue their doors shut!
[quoted text clipped - 9 lines]
>>
>> webpa
MajorDomo@mailcity.com - 10 Jan 2005 01:45 GMT
When one services thousands of vehicles annually, as we
do in our business, many of the simplest lowest cost things
become obvious.  ;)

mike hunt

> > A little silicone, sprayed on the rubber door moldings, works
> > fine
[quoted text clipped - 3 lines]
>     Thanks. I'll have to run out and get some today. Why is it the simplest
> fixes are always the hardest to figure out yourself!?
 
Sign In
Join
My Latest Posts
My Monitored Threads
My Blog
My Photo Gallery
My Profile
My Homepage

Start New Thread
Enable EMail Alerts
Rate this Thread



©2008 Advenet LLC   Privacy Policy - Terms of Use
This website includes both content owned or controlled by Advenet as well as content owned or controlled by third parties.