 |
 | Home | Contact Us | FAQ | Search & Site Map | Link to Us |
 | Sign In | Join | Other 45 Sites in Network |
Car Forum / Dodge / Dodge Trucks / May 2006gauge mounting?
has anyone used the steering column mounts from gauge works by auto meter? as found on Geno's Garage website? im looking at adding some more gauges and looking for the best looking instalation possible. i already have my EGT on the apillar using the mopar srt-10 pillar trim.  Signature-Chris 05 CTD 06 Liberty CRD > has anyone used the steering column mounts from gauge works by auto meter? > as found on Geno's Garage website? Yep. They work well, but do block view of the bottoms of the speedo and tach (tough to see the OD/Off, 4x4, odometer, and cruise indicators). I also have the 3-gauge dash pod that mounts on top of the dash, which I also like. This doesn't block anything, and is easier to read than any of the other gauge positions. I can give you a link to some pictures if you like, but once you've seen one, that's pretty much it. I can tell you that the fit of both the steering column mount and the dash mount are very good. If you go with the dash mount, I'd recommend all electric gauges. This way, you can use a multi-pin connector and make your own wiring harness, which will let you remove the top dash panel with the gauges attached - this makes installation and service down the road very easy, rather than trying to deal with any tubing connectors. If you need to use a mechanical gauge, then you should get the column mount. yes, tom i would aprishiate the link to the dash pod. sounds like some good and bad with the column mount witch the bad im seeing is what i suspected. i wondered how it would block the dash indicators and ease of reading gauges witch you and roy have confirmed my suspisions. my only question about the dash pod would be if they have a 2 gauge mount as i only need/want the 2 extra gauges (remember my truck is a 6 speed) Signature-Chris 05 CTD 06 Liberty CRD > > has anyone used the steering column mounts from gauge works by auto meter? > > as found on Geno's Garage website? [quoted text clipped - 17 lines] > > If you need to use a mechanical gauge, then you should get the column mount. > witch you and roy have confirmed my suspisions. my only question about the > dash pod would be if they have a 2 gauge mount as i only need/want the 2 > extra gauges (remember my truck is a 6 speed) No, it's only a triple. C'mon - you can always use an extra gauge :) I'll get you some pictures later on tonight. Currently, my dash pod is out of my truck (had a gauge go tilt on me - currently getting fixed by Autometer), so you'll be able to see how it mounts, how I did the wiring, etc. I should be able to find some pictures of an installed pod, as well. thanks tom Signature-Chris 05 CTD 06 Liberty CRD > > witch you and roy have confirmed my suspisions. my only question about the > > dash pod would be if they have a 2 gauge mount as i only need/want the 2 [quoted text clipped - 8 lines] > > I should be able to find some pictures of an installed pod, as well. Sorry I didn't get to this last night... First, here's the wiring from the dash - I ran it up alongside one of the defroster ducts. The connector is an 8-position Molex connector, from Radio Shack : http://home.earthlink.net/~tlawrence51/Dash_Wiring.JPG Here's a close-up of the pod, sitting on top of the (removable) dash cover. As you could see in the previous pic, this dash cover piece is just held in with spring clips - very easy to pop out: http://home.earthlink.net/~tlawrence51/Dash_Pod.JPG Here's a shot of the wiring inside the pod. You can see the matching Molex connector that connects to the dash wiring. The aluminum bar across the pod holds two captive nuts, which is how the pod mounts to the cover (note two matching holes in the dash cover for the screws). I drilled the big hole with a hole saw, for the connector/wiring to pass through. Once installed, the connector tucks up inside the empty space in the pod behind the gauges. For reference, here's a picture from approximately driver's eye height of the column-mounted gauges. It's not quite as bad in reality as this picture makes it look, but I do have to move my head and peer around the gauges to see things like the odometer and lower indicator lights: http://home.earthlink.net/~tlawrence51/Column_Pod.JPG thanks again tom. im gonna hang on to this one so ill have it for ref when im a little closer to actually buying the parts. ive got my eye on the BD tripple dog programmer and the rest of the gauges i want as my next 2 things to do to the truck. hopefully comming soon *big grin* Signature-Chris 05 CTD 06 Liberty CRD > Sorry I didn't get to this last night... > [quoted text clipped - 23 lines] > > http://home.earthlink.net/~tlawrence51/Column_Pod.JPG > im a little closer to actually buying the parts. ive got my eye on the BD > tripple dog programmer and the rest of the gauges i want as my next 2 > things > to do to the truck. hopefully comming soon *big grin* Make sure before you commit to a programmer that you give the Smarty a look: http://www.madselectronics.com/products.html Marco's been doing ECM reprogramming for years now, and his CaTCHER ECM's for the older 24V engines have been highly regarded. >> im a little closer to actually buying the parts. ive got my eye on the BD >> tripple dog programmer and the rest of the gauges i want as my next 2 [quoted text clipped - 7 lines] > Marco's been doing ECM reprogramming for years now, and his CaTCHER ECM's > for the older 24V engines have been highly regarded. They are quite the toy. A friend who has a 06 p/s uses one. I've driven it a lot and was really surprised at the difference it makes. The only thing is a question about dc being able to tell that you've been there and knocking a warranty claim. There is a bit of talk on the tdr about it but nothing conclusive. Roy So Tom, next time you're in Dallas, bring your gauge installation skills along. I have a truck that needs fuel pressure and tranny temp gauges installed. Come on, there's pizza and beer in it for ya. :-) Craig C. > has anyone used the steering column mounts from gauge works by auto meter? > as found on Geno's Garage website? I used that on a 2K and it was in they way too much and at time a pia to see. I took it off after a couple of weeks. Try the mount on the top of the dash. Roy >> has anyone used the steering column mounts from gauge works by auto >> meter? [quoted text clipped - 5 lines] > > Roy I have enough gauges without adding more. I don't care what the manifold pressure is. If I had to add a gauge, just because I tow allot, it would be a transmission temperature gauge. SignatureMoParMaN---Remove Clothes To Reply! --SCUD Coordinates 32.61204 North: 96.92993 West-- >>> has anyone used the steering column mounts from gauge works by auto >>> meter? [quoted text clipped - 9 lines] > pressure is. If I had to add a gauge, just because I tow allot, it would > be a transmission temperature gauge. With a Cummins with a auto I'd think a fuel pressure is a must unless it is a newer model. The trans temp is a close second. It still amazes be how quickly they heat up when in reverse, the temp fly's up. Roy >>>> has anyone used the steering column mounts from gauge works by auto >>>> meter? [quoted text clipped - 15 lines] > > Roy I've got an 05 dually. Besides, what are you gonna do if your pressure drops out on the road? I've got a card with a DC number on it to call if that happens. At least with a temp guage on the transmission, you could pull over and wait for it to cool down before burning something up. It's kinda hard to fix a fuel pressure problem when your on the road. SignatureMoParMaN---Remove Clothes To Reply! --SCUD Coordinates 32.61204 North: 96.92993 West-- >>>>> has anyone used the steering column mounts from gauge works by >>>>> auto meter? [quoted text clipped - 22 lines] > and wait for it to cool down before burning something up. It's kinda > hard to fix a fuel pressure problem when your on the road. If the lift pump fails the truck will still run. Some people don't notice any loss of power at all when the lift pump fails. When the lift pump fails it puts extra stress on the injection pump causing it to fail also. If you monitor the fuel pressure you can tell when the lift pump fails and correct the problem before it causes expensive injection pump failure. Fuel pressure gauge: $75.00 Lift pump: $170.00 Injection pump: $1,075.00 SignatureKen >>>>>> has anyone used the steering column mounts from gauge works by >>>>>> auto meter? [quoted text clipped - 32 lines] > Lift pump: $170.00 > Injection pump: $1,075.00 Under warranty my cost will be Zero. SignatureMoParMaN---Remove Clothes To Reply! --SCUD Coordinates 32.61204 North: 96.92993 West-- >>>>>>> has anyone used the steering column mounts from gauge works by >>>>>>> auto meter? [quoted text clipped - 35 lines] >> > Under warranty my cost will be Zero. The cost maybe zero but the bs sucks. The lift pump goes we are on our a.s until towed to the dealer and they order one and it gets to the dealer. The earlier ones you can pop a new lift pump on in a half hour and your on your way. I think even with the newer ones a fuel pressure gauge will give you a heads up if it starts to fail and you can still get to a dealer. Beats being left at the side of the road when it fails totally. Roy >>>>>> has anyone used the steering column mounts from gauge works by >>>>>> auto meter? [quoted text clipped - 28 lines] > If you monitor the fuel pressure you can tell when the lift pump fails and > correct the problem before it causes expensive injection pump failure. I believe with the 05's and up when they fail you are on your a.s, unlike the earlier models where you have some time before th ip goes away. Roy > Fuel pressure gauge: $75.00 > Lift pump: $170.00 > Injection pump: $1,075.00 > I've got an 05 dually. Besides, what are you gonna do if your pressure > drops out on the road? I've got a card with a DC number on it to call if > that happens. My FP gauge tells me when it's time to change my fuel filter. My trans temp gauge tells me when to back off the go pedal, or downshift. Same with my EGT gauge. My TOT lets me know when it's cool enough to shut down. Boost gauge lets me know if a clamp loosened up, or to back off the throttle because I'm about to pop a head gasket. Oil pressure gauge lets me see what my pressure REALLY is - not some stupid idiot-light-turned-sweeper-gauge. And, ummm... oh yeah, my water temp gauge pretty much serves to fill a hole, and back up the stock ECT sensor :) Christopher Thompson wrote: > has anyone used the steering column mounts from gauge works by auto meter? > as found on Geno's Garage website? [quoted text clipped - 3 lines] > > i already have my EGT on the apillar using the mopar srt-10 pillar trim. Why not use a 2 or 3 pod A-Pillar mount? Looks great. > Why not use a 2 or 3 pod A-Pillar mount? Looks great. Probably for the same reason I didn't... a desire to keep the grab handle. >> Why not use a 2 or 3 pod A-Pillar mount? Looks great. > > Probably for the same reason I didn't... a desire to keep the grab handle. My 2001 Ram doesn't have a driver side grab handle. Steering wheel works if needed. Didn't know newer ones had them. > My 2001 Ram doesn't have a driver side grab handle. Steering wheel works > if needed. Didn't know newer ones had them. Yep - the 3rd gens introduced a driver's side grab handle: http://home.earthlink.net/~tlawrence51/Column_Pod.JPG >> My 2001 Ram doesn't have a driver side grab handle. Steering wheel >> works if needed. Didn't know newer ones had them. > > Yep - the 3rd gens introduced a driver's side grab handle: > http://home.earthlink.net/~tlawrence51/Column_Pod.JPG You could put one on a 2nd gen. http://www.dodgeram.org/tech/mods/body/Grab_handle.htm SignatureKen > > Why not use a 2 or 3 pod A-Pillar mount? Looks great. > > Probably for the same reason I didn't... a desire to keep the grab handle. yup Signature-Chris 05 CTD 06 Liberty CRD |
Reply to this Message |
 Sign In
 Join
 My Latest Posts My Monitored Threads My Blog My Photo Gallery My Profile My Homepage Start New Thread Enable EMail Alerts Rate this Thread
|
©2008 Advenet LLC Privacy Policy - Terms of Use
This website includes both content owned or controlled by Advenet as well as content owned or controlled by third parties.