 |
 | Home | Contact Us | FAQ | Search & Site Map | Link to Us |
 | Sign In | Join | Other 45 Sites in Network |
Car Forum / Honda Cars / January 2005Can rain get inside my Honda's door?
Recently I watched a repairman fix my Honda door. With the inside shell off, there is a plastic wrap that has to be cut at the top to get at the hardware behind it. When the repairman reassembled the door he kind of used his hand to get a corner of the plastic to rest back in place. He didn't tape it. I'd say that a few inches of the upper corner of that plastic may not be sealed perfectly. Is this a potential for water to enter inside the door of the car? > Recently I watched a repairman fix my Honda door. With the inside shell off, > there is a plastic wrap that has to be cut at the top to get at the hardware [quoted text clipped - 6 lines] > > Is this a potential for water to enter inside the door of the car? Well, probably not. More potential for drafts and wind noise to penetrate, for sure. JM > Recently I watched a repairman fix my Honda door. With the inside shell off, > there is a plastic wrap that has to be cut at the top to get at the hardware [quoted text clipped - 6 lines] > > Is this a potential for water to enter inside the door of the car? If the cut in the plastic sheet is high up in the door, the chances of water intrusion are small. With a little patience and a heat gun, it is fairly easy to pull the plastic sheet off along the perimeter rather than cutting it. That would be the preferred way to do it. Downside? You are almost guaranteed to get your hair stuck in the glue while working inside the door. > If the cut in the plastic sheet is high up in the door, the chances of > water intrusion are small. With a little patience and a heat gun, it is > fairly easy to pull the plastic sheet off along the perimeter rather > than cutting it. That would be the preferred way to do it. Downside? > You are almost guaranteed to get your hair stuck in the glue while > working inside the door. The cut is in the upper left corner close to the exterior door handle on the driver's side. It was not glued or taped back. It was laid back as the fabric part of the interior door assembly was reinstalled. Its too bad that Honda did not design the door so that weather proofing would be easy to remove and replace when work is done on the mechanical repair of parts. Is this normal on all Hondas? All cars? > Honda did not design the door so that weather proofing would be easy to > remove and replace when work is done on the mechanical repair of parts. Is > this normal on all Hondas? All cars? all cars. designed for ease of assembly, not necessarily ease of repair. most hondas never need their inner door panel removed. there are some older generations of accord that probably should have been designed with a zipper on the weatherproofing, tho :) >> Honda did not design the door so that weather proofing would be easy >> to remove and replace when work is done on the mechanical repair of [quoted text clipped - 4 lines] > are some older generations of accord that probably should have been > designed with a zipper on the weatherproofing, tho :) And does Honda still use that crappy vinyl sheeting? The stuff shrinks and eventually pulls away from the adhesive. Hate that. Why can't they use heavy polyethylene?  SignatureTeGGeR? The Unofficial Honda/Acura FAQ www.tegger.com/hondafaq/ "TeGGeR®" wrote: > >> Honda did not design the door so that weather proofing would be easy > >> to remove and replace when work is done on the mechanical repair of [quoted text clipped - 9 lines] > > Why can't they use heavy polyethylene? My '94 uses polyethylene sheets. When I installed power locks in Dec. 2002 the sheets were in perfect shape, no shrinking, no pulling away from the adhesive. Using a heat gun and a bit of patience, pulling the sheet away from the glue (that looks and feels like chewing gum) was not that big of a challenge. A year later I had to open up the passenger door again to put a bend in the lock rod. At that time the sheet was still in good shape, and did not seem to have suffered any damage from being partially removed and reinstalled. >Recently I watched a repairman fix my Honda door. With the inside shell off, >there is a plastic wrap that has to be cut at the top to get at the hardware [quoted text clipped - 6 lines] > >Is this a potential for water to enter inside the door of the car? Rain will get inside your door any way. The important thing is to make sure the drain holes at the bottom of the door are clear so that the water can get out. -------------- Alex |
Reply to this Message |
 Sign In
 Join
 My Latest Posts My Monitored Threads My Blog My Photo Gallery My Profile My Homepage Start New Thread Enable EMail Alerts Rate this Thread
|
©2008 Advenet LLC Privacy Policy - Terms of Use
This website includes both content owned or controlled by Advenet as well as content owned or controlled by third parties.