95 Integra Alternator replacement

Thread view:

Enable EMail Alerts

Start New Thread

Thread rating:

Nick - 23 Nov 2005 18:15 GMT

Hi Everyone,

I'm going to need to replace the alternator in the next few weeks as I
have 100k miles and getting close to when these begin to fail so I don't want to
be stranded on the road. Anyway, in looking at the factory manual, it doesn't
mention anything about removing the drive shaft to get this out but I know that
it has to be removed as there is no way to slide the alternator out from the top
of the engine. So looking at removing the drive shaft, can I only remove the
shaft from the hub, because from the manual they mention that you need to remove
it from the transmission housing first before you can remove it from the hub.
Also why additional screws, clips will I need to replace the drive shaft back
in? The manual mentions that I'll need to replace the locking tab is there
anything else that I need?

Thanks in advance,
Nick

Reply to this Message

High Tech Misfit - 23 Nov 2005 18:27 GMT

> I'm going to need to replace the alternator in the next few weeks as I
> have 100k miles and getting close to when these begin to fail so I don't
> want to be stranded on the road.

Surely Honda alternators should last a lot longer than that? Is yours
showing any symptoms of imminent failure?

These aren't crappy Delco alternators, you know. :-)

Reply to this Message

Nick - 23 Nov 2005 18:44 GMT

No signs of failure as of yet, but I can recall that on my Accord, it went at
about 106k and must have been the original. (granted I got the car used so who
knows how it was driven before I got it). I have looked at some posts on google
who mention that you don't need to disassemble the driveshaft to get it out. I
wish it was as easy to replace as it was on my Accord :)

Nick

>> I'm going to need to replace the alternator in the next few weeks as I
>> have 100k miles and getting close to when these begin to fail so I don't
[quoted text clipped - 4 lines]
>
>These aren't crappy Delco alternators, you know. :-)

Reply to this Message

AZ Nomad - 23 Nov 2005 18:29 GMT

>Hi Everyone,

> I'm going to need to replace the alternator in the next few weeks as I
>have 100k miles and getting close to when these begin to fail so I don't want to
>be stranded on the road. Anyway, in looking at the factory manual, it doesn't

Funny. I used to have a '93 integra and its shop manual clearly outlined
how the left side lower suspension had to be dissassembled to remove the
alternator.

I took it to a repair shop. They thought it was easier to pull the master
cylinder in order to R&R the alternator.

>mention anything about removing the drive shaft to get this out but I know that
>it has to be removed as there is no way to slide the alternator out from the top
[quoted text clipped - 4 lines]
>in? The manual mentions that I'll need to replace the locking tab is there
>anything else that I need?

>Thanks in advance,
>Nick

Reply to this Message

Frank Boettcher - 24 Nov 2005 16:52 GMT

>Hi Everyone,
>
[quoted text clipped - 12 lines]
>Thanks in advance,
>Nick

1. that is fairly early to replace. and they generally don't fail
catastrophically but the light will come on intermittantly for a
while. when that happens you can tap it and will reseat the brushes
(that is what usually goes first) and it will continue to charge for a
while. My son nursed his through a couple of months and drove home
180 miles from school to give me the time to replace ('90 accord with
155K miles).

2. When it starts to go if you can get a set of brushes and replace
them it is a lot less expensive. Providing your bearings are sound.

3. I don't know about integras but accord four cylinders can come out
trough the top by removing the power steering pump and the cruise
accuator on some models. A whole lot easier than removing a drive
shaft.

Reply to this Message