I replaced my front and rear brakes this weekend. When I did the front
brakes, as I was pushing in the puck I noticed some brake fluid (a
couple of ounces) dripping down from the engine compartment. The new
pads work well, but what I wanted to know is did I possibly screw
anything up? Is my master cylinder or ABS going to die a premature
death?
thanks in advance!
Seth - 20 Feb 2006 03:04 GMT
>I replaced my front and rear brakes this weekend. When I did the front
> brakes, as I was pushing in the puck I noticed some brake fluid (a
> couple of ounces) dripping down from the engine compartment. The new
> pads work well, but what I wanted to know is did I possibly screw
> anything up? Is my master cylinder or ABS going to die a premature
> death?
Where in the engine compartment did it come from? Did you open the brake
fluid reservoir before compressing the caliper to allow the fluid level to
rise easily? Was the amount in the reservoir near the top BEFORE you
serviced your brakes?
Al - 20 Feb 2006 03:18 GMT
It is hard to tell where the fluid came from, but it was not from the
brake fluid reservoir. I was towards the drivers side (oposite site
than the brake fluid reservoir). Yes I did open the brake fluid
reservoir before compressing the caliper.
Any ideas?
Seth - 20 Feb 2006 03:38 GMT
> It is hard to tell where the fluid came from, but it was not from the
> brake fluid reservoir. I was towards the drivers side (oposite site
> than the brake fluid reservoir). Yes I did open the brake fluid
> reservoir before compressing the caliper.
>
> Any ideas?
With your update above, I'm stumped. Was hoping it was something silly you
missed, but doesn't sound like it now.
twfsa - 20 Feb 2006 03:46 GMT
The fluid was coming from the master cylinder reservoir, I usually removsome
fluid before compressing the caliper piston I don't think it did any harm.
It never has on any of my vehicles. How many miles on the Pilot were the
pads wore out?
Tom
>> It is hard to tell where the fluid came from, but it was not from the
>> brake fluid reservoir. I was towards the drivers side (oposite site
[quoted text clipped - 5 lines]
> With your update above, I'm stumped. Was hoping it was something silly
> you missed, but doesn't sound like it now.
Al - 20 Feb 2006 03:50 GMT
Thanks for the warm-and-fuzzy.
I have 57K on the Pilot.
jim beam - 20 Feb 2006 03:59 GMT
> I replaced my front and rear brakes this weekend. When I did the front
> brakes, as I was pushing in the puck I noticed some brake fluid (a
[quoted text clipped - 4 lines]
>
> thanks in advance!
when you push the piston back in, you should always open the bleed
nipple - prevents exactly this kind of thing. it's simply the fluid
rising in the reservoir. wash the spill off with water asap. do NOT
wipe, even after you've washed it. just leave to dry naturally.
discard the the fluid you get from the calipers.
Michael Pardee - 20 Feb 2006 12:30 GMT
>I replaced my front and rear brakes this weekend. When I did the front
> brakes, as I was pushing in the puck I noticed some brake fluid (a
[quoted text clipped - 4 lines]
>
> thanks in advance!
As jim beam says - it happens, but the brake fluid will eat paint if given a
chance. Wash it off completely with water (I like to spray with Simple Green
after the initial rinse and rinse again) very soon.
Mike
jim beam - 20 Feb 2006 16:31 GMT
>>I replaced my front and rear brakes this weekend. When I did the front
>>brakes, as I was pushing in the puck I noticed some brake fluid (a
[quoted text clipped - 10 lines]
>
> Mike
i'd stay well away from simple green if i were you mike. there have
been a lot of reports of stress corrosion cracking in steel with that
stuff, including some bike stuff i bought used. steel eyelets in a rim
cracked and fell apart. that's the last thing /i'd/ want anywhere near
my honda braking system!!!
Al - 21 Feb 2006 00:25 GMT
I just realized that I did NOT remove the brake fluid reservoir, but
the power steering fluid reservoir. I have ordered a shop
manual...Next time, I'll be a bit more careful.
thanks!
Al