 |
 | Home | Contact Us | FAQ | Search & Site Map | Link to Us |
 | Sign In | Join | Other 45 Sites in Network |
Car Forum / Hyundai Cars / March 200699 accent clutch
just had clutch replaced and when you start the car the clutch makes a screethin sound for about a minute till it warms up a bit. sound goes away when I push the clutch in... Usually, bad throwout bearings act just the opposite-- they make a loud screeching noise when the pedal is depressed. Nonetheless, I'd primarily suspect the throwout bearing, but there are a few possibilities. I'd recommend taking it back to the shop that replaced the clutch. > Usually, bad throwout bearings act just the opposite-- they make a loud > screeching noise when the pedal is depressed. Nonetheless, I'd primarily > suspect the throwout bearing, but there are a few possibilities. I'd > recommend taking it back to the shop that replaced the clutch. Sounds more like a pilot bearing to me because as you say - the throw out bearing usually acts just the opposite. The pilot bearing will act just this way.  Signature-Mike- mmarlowREMOVE@alltel.net The pilot bearing is not spinning when the clutch is engaged. It only spins when the pedal is depressed. Chris > The pilot bearing is not spinning when the clutch is engaged. It only > spins when the pedal is depressed. Yes, you are correct Chris. My bad. Signature-Mike- mmarlowREMOVE@alltel.net i just have a feeling theyre gonna blame the non hyundai clutch. hes mentioned it once, in last message i told ya guys what he said.. ive seen a few other 5 spds our vintage and they seem noisy too >> The pilot bearing is not spinning when the clutch is engaged. It only >> spins when the pedal is depressed. > > Yes, you are correct Chris. My bad. Why'd they use a non-Hyundai clutch? If they chose the parts, then I think they'd be on the hook for making sure the parts are correct. Ordinarily, that would be sound logic, but Hyundai doesn't use a pilot bearing. I suppose it could be the input shaft against the crank bushing. That certainly makes a little more sense than my original idea. i remmebr in 2001 they redid all our input shaft berrings > Ordinarily, that would be sound logic, but Hyundai doesn't use a pilot > bearing. I suppose it could be the input shaft against the crank bushing. > That certainly makes a little more sense than my original idea. i have that feeling, i was told to wait a week and see if it changes. itts been a month..... >> Usually, bad throwout bearings act just the opposite-- they make a loud >> screeching noise when the pedal is depressed. Nonetheless, I'd primarily [quoted text clipped - 4 lines] > bearing usually acts just the opposite. The pilot bearing will act just > this way. where is the pilot bearing? i know in clutch kit there was big roiund plastic looking one i think thats the clutch release, the other was a metal bearing about size of a large lifesaver... they told me the car diddnt need the lil one put in it was fine... ( i wassnt impressed when i was told that when picking up) all new parts should have wen t in. so........ since they said thyer diddnt put it in, kinda up to them top refix non? i assume thyre l;ooking for another blame ;like he mentioned if its because not a hyun clutch maybye its sound clutch setting in. thats when i said u did the clutch a month ago, ive done several 8 hrs drives since. should be broken in by now... grrrrrrrr, hes my ex hyun ser manager, now at kia i go there because i trusted him, and he gives me deals... lets see now how much longer i trust.... rear brake still squeeks when sitting still or moving when its applied also. they said thery replaced the cylinder in back and clean/lubed rear brakes. they why still same eek when brake moves inside, or its smeting in there... >> Usually, bad throwout bearings act just the opposite-- they make a loud >> screeching noise when the pedal is depressed. Nonetheless, I'd primarily [quoted text clipped - 4 lines] > bearing usually acts just the opposite. The pilot bearing will act just > this way. > where is the pilot bearing? It is in the center of the flywheel on the back of the engine and is used to support the nose of the transmission shaft. It is what you stick the clutch disk alignment tool into so that the transmission shaft will align with the clutch disk and pilot bearing when you are installing the transmission. Matt Let's see. 1. The noise wasn't there before they replaced the clutch. 2. The noise was present immediately after the clutch was replaced. 3. The noise goes away when depressing the clutch pedal. It would seem to me that the probability of the noise being somehow related to the repair would be rather high. I think the onus is on the repair facility to determine what's causing the noise and stop with the "maybes." > just had clutch replaced and when you start the car the clutch makes a > screethin sound for about a minute till it warms up a bit. > sound goes away when I push the clutch in... How much did that run you? Chris 180.00 and 450.00 cdn $ >> just had clutch replaced and when you start the car the clutch makes a >> screethin sound for about a minute till it warms up a bit. [quoted text clipped - 3 lines] > > Chris > 180.00 and 450.00 cdn $ Which one? Chris 180.00 for clutch 450.00 to put it in >> 180.00 and 450.00 cdn $ > > Which one? > > Chris |
Reply to this Message |
 Sign In
 Join
 My Latest Posts My Monitored Threads My Blog My Photo Gallery My Profile My Homepage Start New Thread Enable EMail Alerts Rate this Thread
|
©2008 Advenet LLC Privacy Policy - Terms of Use
This website includes both content owned or controlled by Advenet as well as content owned or controlled by third parties.