Home | Contact Us | FAQ | Search & Site Map | Link to Us
Sign In | Join | Other 45 Sites in Network
HomeAnnouncements
Discussion Groups
By Brand
BMWChevroletDodgeFordGMHondaLexusMercedes-BenzNissanPeugeotToyotaVolkswagenOther Brands
By Topic
4x4 CarsRVsDrivingMaintenance & RepairCar AudioCollectible Cars
Country Specific
Australian ForumsUK Forums
ArticlesAuto InsuranceBuyingCars & TechnologyMaintenanceMiscellaneousSafety
DMV Resources
Related Topics
MotorcyclesBoatsMore Topics ...

Car Forum / Isuzu Cars / January 2008

Tip: Looking for answers? Try searching our database.

98 Rodeo: Blown head gasket , I think > Worth fixing?

Thread view: 
Enable EMail Alerts  Start New Thread
Thread rating: 
rm - 09 Jan 2008 05:29 GMT
I'm helping a neighbor who overheated his 98 Rodeo (3.2L V6, I believe).
198,000 miles, well maintained.  He had a hole in the radiator and the
temp gauge was pegged. He limped down the shoulder of the freeway to a
gas station. The engine was making clicking/popping sound, he said,
along with lots of steam from under the hood, obviously.

He had it towed to a shop closer to home. They didn't even open the hood
and told him his engine was cooked, and for $3500 they could put in a
rebuilt one.

He knows very little about cars, so he gets in and drives home from the
shop(!!!)....even on the freeway.   The car runs fine all the way home.

Tonight I got some tools and went to the vehicle. Besides the big hole
in the top of the radiator, it looks normal. Oil looks OK.

The car has been sitting outside for a couple of weeks, but I was able
to start it with took LOTS of cranking. It was running real rough and
blew a bunch of water vapor out of the tailpipe.  I thought, yep, engine
toast.  BUT, after shutting the engine down for a bit, I restarted it
and it's running ABSOLUTELY PERFECTLY.

...BUT, after a few minutes of idling, the exhaust started slowly
getting steamier, and steamier, till it was clearly blowing vapor. Head
gasket, correct?

If engine has good compression and the oil is not milky, should he get
the head gaskets done and keep driving it?  I plan to swap the radiator,
run a compression test,inspect the plugs, and swap the oil/coolant,
followed by a cooling system pressure test.

Do these cars tend to crack heads, or just blow the gasket? How much
would a shop charge to pull + service the heads and swap gaskets?

I'm tempted to do the job, as I've done lots of head gaskets, but the
wife may change the house locks if I did, and the bench in the garage is
not a good place to sleep.
John Martinez - 25 Jan 2008 18:50 GMT
I've got a 2002 with a V6.  Head gasket blew under warranty.  I suspect it's
gone again.  Tell tale sign is radiator coolent in oil.

> I'm helping a neighbor who overheated his 98 Rodeo (3.2L V6, I believe).
> 198,000 miles, well maintained.  He had a hole in the radiator and the
[quoted text clipped - 33 lines]
> may change the house locks if I did, and the bench in the garage is not a
> good place to sleep.
GreenGas - 30 Jan 2008 06:33 GMT
> I'm helping a neighbor who overheated his 98 Rodeo (3.2L V6, I believe).
> 198,000 miles, well maintained.  He had a hole in the radiator and the
[quoted text clipped - 33 lines]
> may change the house locks if I did, and the bench in the garage is not a
> good place to sleep.

To answer your question, the answer as to what's wrong could be one of three
things: one or both of the heads could be cracked, one or both of the head
gaskets are blown, or the block (cyliner liner) may be cracked, or all three
of these may exist. You could start by pulling the heads and looking for the
obvious damage to the head gasket, but if you stopped there and put it all
back together, you have more gambling in you than I do. I'd have the heads
checked and with that many miles on it, I'd have them essentially rebuilt,
AFTER checking the cylinder liners as well as possible. Often, the cylinder
that is leaking will have tell-tale remains of antifreeze or marks of water
in it, so you'll know where to focus your attention. Since there isn't water
in the oil, or oil in the water, chances are that the block is ok. Once you
have the heads rebuilt, though, you still have another potential problem -
engines that get that hot often burn oil, since the rings get hot and no
longer will seal properly. To do the job right, you may want to think about
dropping the pan and pulling the pistons, which is a LOT of work, but
doable. Or, you could simply put it back together and expect it to burn oil,
and if it doesn't, then it's great. You can buy a LOT of oil for what it
costs to pull the entire engine and swap it out. I just had a local shop
here price out doing essentially the same job to my 98 Trooper w/ a 3.5, and
the labor alone was around $900. I could do it for a lot less in my garage,
but like you, I'd be sleeping in the carport after I started. Maybe you
should do it, only in your neighbor's garage... and find some excuse to
spend a lot of time over there. Hope this helps.
Steve
 
Sign In
Join
My Latest Posts
My Monitored Threads
My Blog
My Photo Gallery
My Profile
My Homepage

Start New Thread
Enable EMail Alerts
Rate this Thread



©2009 Advenet LLC   Privacy Policy - Terms of Use
This website includes both content owned or controlled by Advenet as well as content owned or controlled by third parties.