Home | Contact Us | FAQ | Search & Site Map | Link to Us
Sign In | Join | Other 45 Sites in Network
HomeAnnouncements
Discussion Groups
By Brand
BMWChevroletDodgeFordGMHondaLexusMercedes-BenzNissanPeugeotToyotaVolkswagenOther Brands
By Topic
4x4 CarsRVsDrivingMaintenance & RepairCar AudioCollectible Cars
Country Specific
Australian ForumsUK Forums
ArticlesAuto InsuranceBuyingCars & TechnologyMaintenanceMiscellaneousSafety
DMV Resources
Related Topics
MotorcyclesBoatsMore Topics ...

Car Forum / Land Rover Cars / November 2007

Tip: Looking for answers? Try searching our database.

Freelander

Thread view: 
Enable EMail Alerts  Start New Thread
Thread rating: 
vertuas - 15 Nov 2007 12:51 GMT
Hi All

I just noticeed something leaking from under the freelander (TD4)

It looks like either water or PAS fluid.  I cann't see anything from the top
of the engine.

Underneath the car is  a big plastic panel, so i cannot see anything that
end either.

Does anyone know how the big plastic panel comes of?  I can see two 10mm
bolts on the rear edge, but thats about it.

Thanks

Vert
Richard - 15 Nov 2007 15:49 GMT
> Hi All
>
> I just noticeed something leaking from under the freelander (TD4)
snip

> Underneath the car is  a big plastic panel, so i cannot see anything that
> end either.
>
> Does anyone know how the big plastic panel comes of?  I can see two 10mm
> bolts on the rear edge, but thats about it.

You will need to raise the front of the car on axle stands (and secure rear
wheels etc) to get under and find all the bolts _and_ screws (unless your a
size zero). Going by memory I think you should find 6 bolts heavy duty
bolts, 2 at rear of panel, 2 mid panel and 2 at front end (extreme left and
right). They are also _about_ 6 screws along the front securing the much
more light weight 'trim like bits'. A quick look around should find them
all. BTW it is quite heavy so take care. When replacing the same I tend to
use a 3 ton trolley jack to hold it more or less in position and to take the
weight while I locate the main bolts etc. Just get them all located and
tightened a bit first.

It is quite easy to remove and replace when you get the knack.

HTH ............... Richard
vertuas - 15 Nov 2007 16:19 GMT
>> Hi All
>>
[quoted text clipped - 21 lines]
>
> HTH ............... Richard

Thanks for that Richard,

I think it is a water leak that i have.  Left the car a few hours and the
drive is dry under the car, looks like its being forced out under pressuse.

The leak is on the cam belt end on the engine.  I reckon it might be the
pump.

Anyone else any other ideas?

thanks

Vert
Dougal - 15 Nov 2007 17:57 GMT
>>>Hi All
>>>
[quoted text clipped - 36 lines]
>
> Vert

Smell/taste the liquid first.

Does it smell like coolant/anti-freeze? Is there a definite taste?

If no to both, do you have air conditioning? I don't know where the a/c
drains are on a Freelander but I'm sure someone will tell you.
Dave Liquorice - 15 Nov 2007 20:41 GMT
> Smell/taste the liquid first.

I'd look first, then feel it, then smell it, for taste I'd have to fairly
convinced from the previous three it was only clean water.

> Does it smell like coolant/anti-freeze? Is there a definite taste?
>
> If no to both, do you have air conditioning? I don't know where the a/c
> drains are on a Freelander but I'm sure someone will tell you.

It might be air con condensate but I wouldn't expect that at this time of
year. Firstly I doubt the air con is actually running, as in cooling and
secondly the air over the UK is fairly dry ATM anyway.

Signature

Cheers                                              new5pam@howhill.com
Dave.                                             pam is missing e-mail

Teeafit - 16 Nov 2007 08:21 GMT
Just to make doubly sure -- it IS the right hand (driver's side) end
of the engine we're talking about?  Not the kerb side?

I mention this because of the condensation drain pipes from the
infernal 'central heating boiler' that lives near the left-hand
headlight, and exhausts just below the bumper ahead of the front
wheel.  This is the time of year when the ambient temperature drops
low enough for it to start coming on, doing (in my experience) very
little to improve the warm-up time of the heater, and increasing the
Chancellor's take on my Road Fuel Tax by a considerable amount.

GRAEME ALDOUS
Yorkshire
vertuas - 16 Nov 2007 08:39 GMT
HI

It is diffinatly the driver side / off side.

It appears to be leaking under pressure, you leav the car to cool and
nothing leaks, you got for drive and get it warm, after it has been standing
still a little while, you get a puddle under it.

Which would support it being collant, and by the position of the leak, i'm
thinking worst case it could be knackered water pump bearings even though
they havent been screaming.

Since it may be water pump bearings, it staying on the driveway as the last
thing i want to do is strip the timing beld when the pump finally ceases up.

Without getting the bottom pan off i can't see whats going on.  Top looks
dry and nothing leaking, again water pump will be nearer the bottom ot the
engine.

Thanks for the help guys.  If anyone know different to me then please post,
cos the only think that i know is that i know nothing.
vertuas - 16 Nov 2007 11:37 GMT
Oh dear

I have just been up to the petrol station, about 3minutes away, with the
freelander.

A noise has become apparent, kind of like a loose belt noise.

hmmmm......water pump bearings??!!

Does anyone know if the pump is on the timing belt?

If it is the car is staying on the drive until it is sorted out...Don't
wanna strip/snap that timing belt!
Richard - 16 Nov 2007 13:15 GMT
> Oh dear
>
> I have just been up to the petrol station, about 3minutes away, with the
> freelander.
> snip

> Does anyone know if the pump is on the timing belt?

I understand that on the TD4 it is 'driven' via an auxiliary drive belt
......... thinking about it further I recall just the petrol Freelanders
have the coolant pump 'driven' via the timing belt ........ but don't quote
me on that last bit.

Richard
vertuas - 16 Nov 2007 13:37 GMT
> I understand that on the TD4 it is 'driven' via an auxiliary drive belt
> ......... thinking about it further I recall just the petrol Freelanders
> have the coolant pump 'driven' via the timing belt ........ but don't
> quote me on that last bit.
>
> Richard

Thanks for that Richard, i just remember what happened to my father's car
when the pump siezed (i learned to spell it now) on the motor way, and
stripped all of the little teeth off the timing belt (that was a ford!).

Kiss your values goodbye!! LMAO
Richard - 16 Nov 2007 16:51 GMT
>> I understand that on the TD4 it is 'driven' via an auxiliary drive belt
>> ......... thinking about it further I recall just the petrol Freelanders
[quoted text clipped - 8 lines]
>
> Kiss your values goodbye!! LMAO

The 'Ford' Freelander 2 uses belt rather than chain as in the BMW TD4. I
wonder if the water pump is driven by the belt too in the Freelander 2
......... knowing Ford I wouldn't be surprised if it is.

Richard
 
Sign In
Join
My Latest Posts
My Monitored Threads
My Blog
My Photo Gallery
My Profile
My Homepage

Start New Thread
Enable EMail Alerts
Rate this Thread



©2008 Advenet LLC   Privacy Policy - Terms of Use
This website includes both content owned or controlled by Advenet as well as content owned or controlled by third parties.