 |
 | Home | Contact Us | FAQ | Search & Site Map | Link to Us |
 | Sign In | Join | Other 45 Sites in Network |
Car Forum / Land Rover Cars / November 2005Rocker cover air pressure
Perhaps someone can give the benefit of their technical knowledge, I have recently discovered air being pushed out of the gasket under the rocker cover on my 110 2.5D. I have ordered a new gasket to replace the old grotty one, but a number of people I have mentioned this to have expressed surprise that I have air pressure inside the rocker cover at all. I have tried removing the breather tube from the oil filer cap, and sure enough there is air being pumped out of the filler cap as the engine idles. This seems strange given that there is a filter inside the cap which would indicate to me that air is supposed to flow into the rocker cover not out. Frightening phrases such as 'crank case over pressure' and 'piston replacement' have also been mentioned, so my questions are: Should air be blown out of the rocker cover or sucked in? If it should be sucked in why is mine being blown out and how do I fix this? In trepidation... Smudge > Should air be blown out of the rocker cover or sucked in? Blown out - any compression that travels past the piston rings has to go somewhere, hence having a breather on the rocker cover. > If it should be sucked in why is mine being blown out and how do I fix > this? If you are suffering from excessive pressure it's a fair sign that pistons/rings are worn and the engine is on it's way out. And lets face it the old 2.5D wasn't the most long lived engine on earth so it's distinctly possible that yours is worn out.  SignatureEMB >Should air be blown out of the rocker cover or sucked in? Definately should be blowing out. The more it blows the more knackered the engine is. When it starts blowing oil out past the gasket and popping the cap off regularily start considering the rebuild! Even after being rebuilt, my engine still feels like its blowing quite a bit - but its an awful lot less than it used to and its now easily oil tight. Breather pipes can block up. I'm not conversant with this engine or its idiosyncrasies, so I don't know where it leads the crankcase pressure, but I do suggest you check the breather system for blockages. Tony > Perhaps someone can give the benefit of their technical knowledge, I > have recently discovered air being pushed out of the gasket under the [quoted text clipped - 17 lines] > > Smudge > Should air be blown out of the rocker cover or sucked in? > > If it should be sucked in why is mine being blown out and how do I fix > this? > > In trepidation... Trepidate not my friend. It should blow out. All of these engines will blow and will regularly wear the rubber ring-seal on the filler cap so that it leaks like a sieve.There should be a pipe leading from the cap to the air inlet manifold or piping which sucks all the fumes into the engine to be consumed by hellfire. A new three-ringed cap seal thing has been needed on mine every couple of years for the last twenty. It lasts about as long as the accelerator pedal cable, which is also needed every couple of years. Don't even consider an overhaul based on a bit of hot air. Huw > It lasts about as long as the >accelerator pedal cable, which is also needed every couple of years. >Don't even consider an overhaul based on a bit of hot air. My 2a (with a 2.5n/aD) has an accelerator linkage that looks like it may be made out of a bit of heavy duty coathanger metal. Its never broken! Many thanks for all your wisdom, I can now change my gasket and sleep easier! Next job, a new heater to fit... Smudge >> It lasts about as long as the >> accelerator pedal cable, which is also needed every couple of years. [quoted text clipped - 3 lines] > may be made out of a bit of heavy duty coathanger metal. Its never > broken! The difference between men and boys is how hard they work their toys. Huw |
Reply to this Message |
 Sign In
 Join
 My Latest Posts My Monitored Threads My Blog My Photo Gallery My Profile My Homepage Start New Thread Enable EMail Alerts Rate this Thread
|
©2008 Advenet LLC Privacy Policy - Terms of Use
This website includes both content owned or controlled by Advenet as well as content owned or controlled by third parties.