 |
 | Home | Contact Us | FAQ | Search & Site Map | Link to Us |
 | Sign In | Join | Other 45 Sites in Network |
Car Forum / Porsche / Porshe 944 / April 2006944 Clutch
Seen some high quotes (some extortionate) for replacing the clutch. Is it really that hard?  SignatureRegards, Dave dave_ryman@hotmailNOSPAM.com http://welcome.to/daves.website http://travel.to/formula.one Not hard, but labor intensive. > Seen some high quotes (some extortionate) for replacing the clutch. Is it > really that hard? what devil's said, but with the following caveat - you must have decent mechanical skills - I've done this twice - second time was easier - took about 8 to 10 hours, working pretty fast, with a helper, no surprises, and all the parts on hand. procedure can be summarized as: remove starter motor remove exhaust (muffler and cat) disconnect axles disconnect shift lever (inside car) disconnect shift linkage, etc, decouple drive shaft at rear remove trans remove rear flywheel sensor remove clutch slave cyl, various clamps remove drive shaft and housing remove clutch exchange disk reassemble everything >Not hard, but labor intensive. > >> Seen some high quotes (some extortionate) for replacing the clutch. Is it >> really that hard? Bill www.wbnoble.com to contact me, do not reply to this message, instead correct this address and use it will iam_ b_ No ble at msn daught com > what devil's said, but with the following caveat - you must have > decent mechanical skills - I've done this twice - second time was [quoted text clipped - 29 lines] > will iam_ b_ No ble at msn daught com > *** Posted via a free Usenet account from http://www.teranews.com *** Thanks for that - should keep a mechanic busy for a while! SignatureRegards, Dave dave_ryman@hotmailNOSPAM.com http://welcome.to/daves.website http://travel.to/formula.one Anyone out there have a decent used clutch & Presure plate? I am going to replace the rubber auto flex plate with it. Also lookinh looking for a bellhousinh set up for the clutch. yes, I have a good used clutch - I just did a clutch job on my daughter's car and replaced everything - it's just too much work not to - the clutch is fine (the disk of course was junk), throwout bearing is "ok", in my opinion it would last another 50 to 100K miles if you want it, contact me off the list, make me a reasonable offer - I don't think it will fit in a flat rate box, but if you are interested, I can check, that would save you $ in shipping >Anyone out there have a decent used clutch & Presure plate? I am going >to replace the rubber auto flex plate with it. Also lookinh looking for >a bellhousinh set up for the clutch. Bill www.wbnoble.com to contact me, do not reply to this message, instead correct this address and use it will iam_ b_ No ble at msn daught com please send me your email address I cant seem to get it working . I am at M G D O T C O M @ G M A I L . COHM to make things easy for anyone else who wants to find me, go to my web site, www.wbnoble.com - I have a photo of my email address there that works - I don't put it in text on the internet as a means of reducing spam - and yes, it' works. >please send me your email address I cant seem to get it working . >I am at M G D O T C O M @ G M A I L . COHM Bill www.wbnoble.com to contact me, do not reply to this message, instead correct this address and use it will iam_ b_ No ble at msn daught com |
Reply to this Message |
 Sign In
 Join
 My Latest Posts My Monitored Threads My Blog My Photo Gallery My Profile My Homepage Start New Thread Enable EMail Alerts Rate this Thread
|
©2009 Advenet LLC Privacy Policy - Terms of Use
This website includes both content owned or controlled by Advenet as well as content owned or controlled by third parties.