 |
 | Home | Contact Us | FAQ | Search & Site Map | Link to Us |
 | Sign In | Join | Other 45 Sites in Network |
Car Forum / Toyota / Toyota Cars / October 2006Help, please: 1983 Cressida radio problem
Help, please... I love my '83 Cressida... it runs very well... almost everything works... the problem I'd like to fix is that the radio doesn't remember the stations when the ignition is turned off. If I turn off the radio while driving, then turn it on again, the memorized stations are still there, but not after the engine is re-started. It's the stock AM/FM/Cassette with equalizer. I've got the wiring diagram... it has the 5-pin "A" connector and the 9-pin "B" connector. The B3 pin is hot when the ignition is on (I assume that's power to the radio) and the A4 pin is hot Always (even when the ignition is off). I would think that that A4 pin should supply the power to remember the radio stations. Is the problem Inside the radio? I'd rather not take it apart, but I will if you tell me of something specific that I could check out. Any clues? Thanks in advance for any ideas. > Help, please... I love my '83 Cressida... it runs very well... > almost everything works... the problem I'd like to fix is that the [quoted text clipped - 14 lines] > > Thanks in advance for any ideas. I don't know about Toyotas, but my old lincoln has a fuse that controled this. Until I replaced the fuse I had no radio memory. > Help, please... I love my '83 Cressida... it runs very well... > almost everything works... the problem I'd like to fix is that the [quoted text clipped - 14 lines] > > Thanks in advance for any ideas. You've done well, my son! ;) Now, the question is, did you discerne that the wires are hot when you looked at the wiring diagram, or did you measure them with a meter?! If you measured them with a meter, and the A4 pin has 12V with the ignition OFF, then the problem is porbably in the radio. One more question, though: did you ohm out the Ground wires? Even though the chassis will ground the radio, that particular circuit may be isolated from the chassis (I don't see why, but who knows why engineers do things the way they do?) Ckeck that, and also check the radio to see if there are any fuses on it. Some of them had a fuse in the back under the connector, but most of them have internal, soldered-in fuses that require "Servicing by a qualified technician" :) Perhaps I may be able to be persuaded to part with the same radio from my Supra. Let me know how you make out. I like to keep stuff that came with the car, just so I can say it's 'complete', but I'm never going to use it! I went to the Evil Wal*Mart and bought a 'harness' for Toyotas, and installed a JVC AM/FM/CD/MP3 player with an Alpine EQ. Beats the crap out of the Stock radio! > You've done well, my son! ;) Thanks for the discussion, people. Mr. Insanity... According to the wiring diagram, the wire that's always Hot is hooked up to the 15 amp fuse that also runs the horn. The horn works, so I don't think that's the problem. Like I said, that wire has electricity going to it all the time. Dad... (hehe)... no meter used... I used alligator clips to hook up a 12v light bulb. Yes, the A4 pin has electricity (how many volts/watts?... I dunno') when the key is off. "Ohm out the ground wires"? I'm not sure what that means, but the wiring diagram says that the B7 pin is supposed to be grounded... So I hooked up the alligator clips and light bulb to A4 and B7... it works, so B7 apparently is grounded. Can't find any fuses on the radio. I think I could replace an internal soldered-in fuse... I guess it's time to open it up, eh? Yes,... I'm sure a new radio would sound infinately better, but I'm a cheap bastard... why else would I be drivin' an '83 Toyota!? (hehe) Any other clues? Thanks again, people. >> You've done well, my son! ;) > [quoted text clipped - 8 lines] > a 12v light bulb. Yes, the A4 pin has electricity (how many > volts/watts?... I dunno') when the key is off. Dad? (!)! Is rthat like when the youger guys at the 'Club' used to call me 'Pops'? > "Ohm out the ground wires"? I'm not sure what that means, but the > wiring diagram says that the B7 pin is supposed to be grounded... So I > hooked up the alligator clips and light bulb to A4 and B7... it works, > so B7 apparently is grounded. Yeah, I'd say so... > Can't find any fuses on the radio. I think I could replace an internal > soldered-in fuse... I guess it's time to open it up, eh? This is an educated guess. You can get the radio repaired (actually, probably swapped out) for $75 from United Radio. > Yes,... I'm sure a new radio would sound infinately better, but I'm a > cheap bastard... why else would I be drivin' an '83 Toyota!? (hehe) > > Any other clues? Thanks again, people. Go ta Wal*Mart and pick up a $35 radio to boot! >> You've done well, my son! ;) > [quoted text clipped - 21 lines] > > Any other clues? Thanks again, people. You are on the right track. Next step is to open up the radio and follow the circuit from A4.  SignatureRay O (correct punctuation to reply) You called me "Son", so I called you "Dad" (hehe) Heck,... I'm probly older than you, anyway. A $35 Wallymart radio is a possible solution, but I'd rather get this original thing working. Mr. Ray,... I opened it up... all of the pins from the A and B connectors go directly to a PC board. It would be a real tricky operation for me to try to further track that circuit. Would that really result in any progress, or just parts that I would have a hard time re-assembling? Couldn't see any fuses inside, either. Any other clues? Thanks, y'all. > You called me "Son", so I called you "Dad" (hehe) Heck,... I'm > probly older than you, anyway. LOL! Ah, yes! So I did! > A $35 Wallymart radio is a possible solution, but I'd rather get this > original thing working. [quoted text clipped - 8 lines] > > Any other clues? Thanks, y'all. Wow...I'd be looking for a burnt resistor, or a capacitor that ain't capacatin'! and, a fuse on the ckt board will look like a resistor, so your trusty OHM meter is a vauled item! Chances are a soldered in fuse will be white, light green or beige, and will look like a resistor, except it will have one distinct, sharp bulge at each end (unlike a resistor, which has a smooth hour-glass shape) and should ohm out to Zero if good, or infinite if bad. If this is it, it's a $0.99 fix! |
Reply to this Message |
 Sign In
 Join
 My Latest Posts My Monitored Threads My Blog My Photo Gallery My Profile My Homepage Start New Thread Enable EMail Alerts Rate this Thread
|
©2008 Advenet LLC Privacy Policy - Terms of Use
This website includes both content owned or controlled by Advenet as well as content owned or controlled by third parties.