Yes, it is possible that you have the incorrect remote, and another FCC ID
is probably incompatible.

There is another possibility, and that is that the remote is a Securikey
system installed by Southeast Toyota Distributors of Gulf States Toyota
Distributors.  If that is the case, try this:

This set of instructions came from the internet, so its accuracy is unknown.
This is for the "Sekuri-Key" system found in the Gulf States and
"South East Toyota". This is not a factory Toyota unit, but it may be port
installed in your car/truck from these regions.

PROGRAMMING ADDITIONAL or REPLACEMENT TRANSMITTERS

Each SECURIKEY+ system can be operated by up to four (4) different
SECURIKEY+ transmitters. The system is supplied from the factory with two
(2) transmitters included, and additional transmitters are available through
parts distribution. Any new or replacement transmitters will need to be
programmed to the main control module before they will activate the system.
The SECURIKEY+ main control module uses a six (6) channel radio frequency
receiver; each channel controlling a different function of the SECURIKEY+
system. Each transmitter button can be programmed to only one of the
receiver channels (e.g., the GREEN button cannot be programmed to operate
the headlight feature and remote start option; it can operate only one or
the other feature). The following is a list of each receiver channel, and
the function of each channel.

CHANNEL #   FEATURE CONTROLLED BY THIS CHANNEL
1       Lock
2       Unlock
3       Trunk Release (optional kit required; not available on all models)
4       30 second headlight activation (only if required by GREEN button)
5       Remote panic (only if required by GREEN button instead of LOCK
button)
6       Remote start (optional kit required; not available on all models)

To program new or additional transmitters, or when adding options to
existing SECURIKEY+ transmitters, follow the step by step programming
instructions found below. When programming, it is important to complete each
step of the procedure within 15 seconds, or the system will terminate the
programming mode. If this happens, simply start again.

Be sure that the SECURIKEY+ system is disarmed, and the lighted valet switch
is in the off (out) position before you begin.
Turn the vehicle's ignition key to the on position.
Press then release the L.E.D. valet switch 6 times.
CHANNEL 1: LOCK & Panic Feature   Horn Chirps 1 Time   L.E.D. Flashes 1 Time
To program the LOCK button on the transmitter, press and hold the LOCK
button until the vehicle's horn sounds one loud chirp. Repeat this for all
transmitters that need the LOCK button programmed (up to four transmitters).
After the LOCK button on all transmitters have been programmed, press and
release the L.E.D. valet switch 2 times to advance to the next receiver
channel.

CHANNEL 2: UNLOCK Feature   Horn Chirps 2 Times   L.E.D. Flashes 2 Times
To program the UNLOCK button on the transmitter, press and hold the UNLOCK
button until the vehicle's horn sounds one loud chirp. Repeat this for all
transmitters that need the UNLOCK button programmed (up to four
transmitters).
After the UNLOCK button on all transmitters have been programmed, press and
release the L.E.D. valet switch 2 times to advance to the next receiver
channel.

CHANNEL 3: TRUNK RELEASE Option   Horn Chirps 3 Times   L.E.D. Flashes 3
Times
To program the TRUNK RELEASE option on the transmitter, press and hold the
GREEN option button until the vehicle's horn sounds one loud chirp. Repeat
this for all transmitters that need the GREEN option button programmed (up
to four transmitters).
After the TRUNK RELEASE button on all transmitters have been programmed,
press and release the L.E.D. valet switch 2 times to advance to the next
receiver channel.

CHANNEL 4: 30 SECOND HEADLIGHT Feature   Horn Chirps 4 Times   L.E.D.
Flashes 4 Times
To program the HEADLIGHT option on the transmitter, press and hold the GREEN
option button until the vehicle's horn sounds one loud chirp. Repeat this
for all transmitters that need the GREEN option button programmed (up to
four transmitters).
After the HEADLIGHT button on all transmitters have been programmed, press
and release the L.E.D. valet switch 2 times to advance to the next receiver
channel.

CHANNEL 5: Separate PANIC Button Feature   Horn Chirps 5 Times   L.E.D.
Flashes 5 Times
To program the PANIC option on the transmitter, press and hold the GREEN
option button until the vehicle's horn sounds one loud chirp. Repeat this
for all transmitters that need the GREEN option button programmed (up to
four transmitters).
After the PANIC button on all transmitters have been programmed, press and
release the L.E.D. valet switch 2 times to advance to the next receiver
channel.

CHANNEL 6: REMOTE START Feature   Horn Chirps 6 Times   L.E.D. Flashes 6
Times
To program the REMOTE START option on the transmitter, press and hold the
GREEN option button until the vehicle's horn sounds one loud chirp. Repeat
this for all transmitters that need the GREEN option button programmed (up
to four transmitters).
After the REMOTE START button on all transmitters have been programmed,
press and release the L.E.D. valet switch 2 times to advance to terminate
programming mode, or simply turn the ignition key to the off position to
terminate the transmitter programming mode.

PROGRAMMING THE SELECTABLE FEATURES
The SECURIKEY+ system offers a number of selectable features that can be
changed, allowing you to custom fit the system to your customer. The
following is a list of the features that are selectable and can be changed
using the valet switch and any transmitter that is programmed to the system
installed in the vehicle.

FEATURE #   FUNCTION 1 CHIRP   2 CHIRPS
1       Headlights on for 20 seconds during disarm ON      or      OFF
2       Headlights on for 20 seconds during arm ON      or      OFF
3       Automatic ignition controlled door lock ON      or      OFF
4       Automatic ignition controlled door unlock ON      or      OFF
5       Auto unlock driver's door only or all doors Driver's door         or
     All doors
6       Active or Passive arming Passive      or      Active
7       Active or Passive door locks Passive      or      Active
8       Trunk release output - 1 second or latched 1 second      or
Latched
9       Panic on lock button or option button Option      or      Lock
10       Trunk Release Hold - 1 second or 2 presses    Hold 1 Sec      or
  2 Times

To change the selection of any of these features, follow the step by step
programming procedures, and do not allow more then 15 seconds to pass
between any two steps or the system will terminate the programming mode.
There is no need to complete the entire programming sequence. After the
appropriate features have been changed, simply turn the ignition key off to
terminate the programming mode.

Be sure that the SECURIKEY+ system is disarmed, and the lighted valet switch
is in the off (out) position before you begin.
Turn the vehicle's ignition key to the on position.
Press then release the L.E.D. valet switch 6 times.
Immediately turn the ignition key off then back on.
FEATURE 1   LED Flashes 1 Time
1 Chirp = Headlights ON During Disarm    Horn Chirps either 1 or 2 Times
2 Chirps = Headlights OFF During Disarm
To change the selection, press and release the lock button on the
transmitter, which will be indicated by the appropriate 1 or 2 chirp signal
from the horn. If you do not want to change this feature, simply press and
release the L.E.D. valet switch 2 times to advance to programmable feature
number 2.

FEATURE 2   LED Flashes 2 Times
1 Chirp = Headlights ON During Arm    Horn Chirps either 1 or 2 Times
2 Chirps = Headlights OFF During Arm
To change the selection, press and release the lock button on the
transmitter, which will be indicated by the appropriate 1 or 2 chirp signal
from the horn. If you do not want to change this feature, simply press and
release the L.E.D. valet switch 2 times to advance to programmable feature
number 3.

FEATURE 3   LED Flashes 3 Times
1 Chirp = Ignition controlled door locks ON    Horn Chirps either 1 or 2
Times
2 Chirps = Ignition controlled door locks OFF
To change the selection, press and release the lock button on the
transmitter, which will be indicated by the appropriate 1 or 2 chirp signal
from the horn. If you do not want to change this feature, simply press and
release the L.E.D. valet switch 2 times to advance to programmable feature
number 4.

FEATURE 4   LED Flashes 4 Times
1 Chirp = Ignition controlled unlock ON    Horn Chirps either 1 or 2 Times
2 Chirps = Ignition controlled unlock OFF
To change the selection, press the lock button on the transmitter, which
will be indicated by the appropriate 1 or 2 chirp signal from the horn. If
you do not want to change this feature, simply press and release the L.E.D.
valet switch 2 times to advance to programmable feature number 5.

FEATURE 5   LED Flashes 5 Times
1 Chirp = Ignition controlled unlock DRIVER'S DOOR    Horn Chirps either 1
or 2 Times
2 Chirps = Ignition controlled unlock ALL DOORS
To change the selection, press the lock button on the transmitter, which
will be indicated by the appropriate 1 or 2 chirp signal from the horn. If
you do not want to change this feature, simply press and release the L.E.D.
valet switch 2 times to advance to programmable feature number 6.

FEATURE 6   LED Flashes 6 Times
1 Chirp = PASSIVE ARMING (Automatic Arming)    Horn Chirps either 1 or 2
Times
2 Chirps = ACTIVE ARMING (Arm by Remote Only)
To change the selection, press the lock button on the transmitter, which
will be indicated by the appropriate 1 or 2 chirp signal from the horn. If
you do not want to change this feature, simply press and release the L.E.D.
valet switch 2 times to advance to programmable feature number 7.

FEATURE 7   LED Flashes 7 Times
1 Chirp = PASSIVE DOOR LOCKS    Horn Chirps either 1 or 2 Times
2 Chirps = ACTIVE DOOR LOCKS
To change the selection, press the lock button on the transmitter, which
will be indicated by the appropriate 1 or 2 chirp signal from the horn. If
you do not want to change this feature, simply press and release the L.E.D.
valet switch 2 times to advance to programmable feature number 8.

FEATURE 8   Do not change this feature selection. It should be left in the
factory preset (1 chirp) mode. Press and release the L.E.D. valet switch 2
times to advance to programmable feature 9.

FEATURE 9   LED Flashes 9 Times
1 Chirp = Remote Panic / GREEN transmitter button    Horn Chirps either 1 or
2 Times
2 Chirps = Remote Panic / LOCK transmitter button
To change the selection, press the lock button on the transmitter, which
will be indicated by the appropriate 1 or 2 chirp signal from the horn. If
you do not want to change this feature, simply press and release the L.E.D.
valet switch 2 times to advance to programmable feature number 10.

FEATURE 10   LED Flashes 10 Times
1 Chirp = Trunk Release HOLD GREEN BUTTON 1 SECOND    Horn Chirps either 1
or 2 Times
2 Chirps = Trunk Release PRESS GREEN BUTTON 2 TIMES
To change the selection, press the lock button on the transmitter, which
will be indicated by the appropriate 1 or 2 chirp signal from the horn. If
you do not want to change this feature, simply press and release the L.E.D.
valet switch 2 times to exit the programming mode.