 |
 | Home | Contact Us | FAQ | Search & Site Map | Link to Us |
 | Sign In | Join | Other 45 Sites in Network |
Car Forum / Volvo Cars / July 2004Front pad 88 Volvo Estate
How do I change the front pads on my 88 Volvo Estate. In an earlier contribution to this discussion, > How do I change the front pads on my 88 Volvo Estate. What model?  SignatureCheers, Bonnet Lock ______ Please reply to newsgroup. Reply address is invalid. 1988 740 Estate > In an earlier contribution to this discussion, > > > How do I change the front pads on my 88 Volvo Estate. > > What model? Check in your Haynes or Chilton workshop manual. Cheers, Peter. : 1988 740 Estate : [quoted text clipped - 9 lines] : > ______ : > Please reply to newsgroup. Reply address is invalid. Good idea, except the manual will not give you tips also is will not answer questions you pose it. > Check in your Haynes or Chilton workshop manual. > [quoted text clipped - 13 lines] > : > ______ > : > Please reply to newsgroup. Reply address is invalid. If you read it and apply your common sense it will answer any question you pose. Try not to act like a retard theres a good chap. Cheers, Peter. : Good idea, except the manual will not give you tips also is will not answer : questions you pose it. [quoted text clipped - 16 lines] : > : > ______ : > : > Please reply to newsgroup. Reply address is invalid. I not the written word not the most difficult to understand. The manual does not always show you the easiest way to do a job. Would rather listen to " additional " advise via a newsgroup before taking on a job I have never done. " Measure twice cut once " > If you read it and apply your common sense it will answer any question you pose. > Try not to act like a retard theres a good chap. [quoted text clipped - 21 lines] > : > : > ______ > : > : > Please reply to newsgroup. Reply address is invalid. In an earlier contribution to this discussion, >> In an earlier contribution to this discussion, >> [quoted text clipped - 7 lines] >> ______ >> Please reply to newsgroup. Reply address is invalid. > 1988 740 Estate I have a parts list - but not repair instructions for this model. From what I can deduce from the picture, the front brakes are broadly similar - but not identical - to those on my 1999 V70. In general terms, for each front wheel: * Turn the steering so that the wheel in question is pointing outwards * Jack up the front of the car and remove the roadwheel * Compress the hydraulic cylinder to provide clearance between disc and pads [Do this with a pair of pliers or G-clamp between the pad and back of the cylinder. DO NOT lever on the disc. Make sure that the master cylinder doesn't overflow - sucking excess fluid out with an old hypodermic syringe (minus needle!) if necessary] * The cylinder assembly is fastened to a bracket attached to the hub assembly by one or two large bolts - which allows it to move sideways slightly to press both pads against the disc. Remove this bolt/these bolts and carefully pull the cylinder assembly - complete with pads - forward, clear of the disc. [Leave the flexible hydraulic hose attached, and support the cylinder assenbly so as not to strain the hose * The handbook should specify a minimum permissible disc thickness and maximum permissible runout. [You will need a micrometer and dial gauge to measure these. BOTH discs must be replaced if either is out of spec or badly scored] * Assuming the discs are ok, fit the new pads in place of the old one - taking careful note of the position of any anti-squeal shims - and re-assemble *Pump the brake pedal a few times to centre the pads SignatureCheers, Bonnet Lock ______ Please reply to newsgroup. Reply address is invalid. True?? I've changed pads on our 240's many times, and one does not need to remove the caliper from the hub to swap out the pads. Does the 740 require caliper removal to change pads?? Further, does it have a sliding-caliper mechanism, not the solid caliper with cylinder-driven pistons for both inner andouter pads?? ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ To send email, remove all < > and [ ] and the junk ~ between: [brucepick1] < a~t > [comcast.net] > In an earlier contribution to this discussion, > [quoted text clipped - 38 lines] > re-assemble > *Pump the brake pedal a few times to centre the pads In an earlier contribution to this discussion, > True?? > [quoted text clipped - 5 lines] > Further, does it have a sliding-caliper mechanism, not the solid > caliper with cylinder-driven pistons for both inner andouter pads?? From the illustation in an old VADIS system to which I have access, the caliper has 2 pistons - both on the same side - and has to slide in order to balance the forces. It *looks* similar to a 70-series caliper - where the pads are fitted first, and the caliper slid over the top - rather than like the sort where the pads are held in by pins, enabling them to be removed without removing the caliper. SignatureCheers, Bonnet Lock ______ Please reply to newsgroup. Reply address is invalid. |
Reply to this Message |
 Sign In
 Join
 My Latest Posts My Monitored Threads My Blog My Photo Gallery My Profile My Homepage Start New Thread Enable EMail Alerts Rate this Thread
|
©2008 Advenet LLC Privacy Policy - Terms of Use
This website includes both content owned or controlled by Advenet as well as content owned or controlled by third parties.