 |
 | Home | Contact Us | FAQ | Search & Site Map | Link to Us |
 | Sign In | Join | Other 45 Sites in Network |
Car Forum / Volvo Cars / March 2006Problems with exhaust system in Volvo 740!
Hello! I must repair exhaust system in my own Volvo 740. I think that exhaust system is original ( the year 1988 , 400 000km). The car noisily works and at times , has a small power (the probably back silencer can be blocked up remainders of the central silencer and may be to choke the engine, is the truth??). The exhaust manifold is all conoded, on exterior and screws holding of him to the cap, are all damage (conoded)...gasket is conoded. I think that when I will touch these screws then they will fall off. Is some possibility, that to screw on afterwards again the exhaust manifold, without taking out of the engine or openings of the cap??  SignatureJarek (SQ1EUO) - V740 B230F + LPG (1988) sq1euo@wp.pl sq1euo@stud.pam.szczecin.pl GG: 1277234 > Hello! > I must repair exhaust system in my own Volvo 740. [quoted text clipped - 12 lines] > some possibility, that to screw on afterwards again the exhaust manifold, > without taking out of the engine or openings of the cap?? I don't think I understand. It doesn't sound like you need to remove the exhaust manifold from the engine, and if you can stay away from that you will be happier. Disconnect the exhaust pipe from the manifold; the screws may break but you will want to use new ones anyway. Get a new "collector" gasket for that place, too. If the exhaust is blocked up, it will show up on the manifold pressure. If you connect a manifold pressure guage and rev the engine to about 2000 rpm for a few seconds then release it, the pressure should return to the idle pressure within two seconds. If it stays high for a couple seconds or doesn't return to idle pressure for several seconds the exhaust is probably blocked. Mike >> Hello! >> I must repair exhaust system in my own Volvo 740. [quoted text clipped - 18 lines] > may break but you will want to use new ones anyway. Get a new "collector" > gasket for that place, too. But problem is with screws, because the remainders of collector's screws will be in engin's cap and I can't put the new screws on this! > If the exhaust is blocked up, it will show up on the manifold pressure. If > you connect a manifold pressure guage and rev the engine to about 2000 rpm > for a few seconds then release it, the pressure should return to the idle > pressure within two seconds. If it stays high for a couple seconds or > doesn't return to idle pressure for several seconds the exhaust is > probably blocked. I don't understand. What pressure? How can I check that the exhaust is blocked up?? Signature-- Jarek (SQ1EUO) - V740 B230F + LPG (1988) sq1euo@wp.pl sq1euo@stud.pam.szczecin.pl GG: 1277234 >>> Hello! >>> I must repair exhaust system in my own Volvo 740. [quoted text clipped - 21 lines] > But problem is with screws, because the remainders of collector's screws > will be in engin's cap and I can't put the new screws on this! I see - you do have to get the manifold off. I've never done it, but maybe somebody here who has can help you. Normally they heat the nuts red hot with a torch before trying to turn them, and even then it's not good. The broken studs can be removed from the cylinder head, but the manifold has to be off first. I'm sorry this has happened to you. It will be a lot of work. >> If the exhaust is blocked up, it will show up on the manifold pressure. >> If you connect a manifold pressure guage and rev the engine to about 2000 [quoted text clipped - 5 lines] > I don't understand. What pressure? How can I check that the exhaust is > blocked up?? The vacuum or air pressure in the intake manifold comes from the engine pumping air through the exhaust. If the exhaust is not blocked, the vacuum returns quickly because the air is being pumped from the intake to the exhaust. If the exhaust is blocked the air gets stuck in the exhaust and when the engine goes back to idle it can't suck the air from the intake manifold and push it to the exhaust right away. So if you hook a guage up to the vacuum part of the intake manifold and rev the engine up then let it go back to idle, the guage will drop quickly if the exhaust is okay but will try to stay high if the exhaust is blocked. Mike > Hello! > I must repair exhaust system in my own Volvo 740. [quoted text clipped - 11 lines] > possibility, that to screw on afterwards again the exhaust manifold, without > taking out of the engine or openings of the cap?? The leak may not be at the manifold gasket (where the manifold joins the cylinder head) but rather lower down, where the manifold joins the exhaust (the flange gasket). These leaks sound very similar. The flange gasket is much easier to repair. If it is the manifold gasket and you do break a stud when attempting to remove the nut, then you must drill out the remaining piece of the broken stud, and tap the hole for a new stud. If you have never used a tap and die set, this would not be the place to start learning; take it to a mechanic. SignatureCheers Andrew <--- Remove The NO and SPAM When Replying ---> Uzytkownik "Andrew McKenna" : > The leak may not be at the manifold gasket (where the manifold joins the > cylinder head) but rather lower down, where the manifold joins the exhaust > (the flange gasket). These leaks sound very similar. The flange gasket is > much easier to repair. Yeah,...You've right,...I don't know when the leak is,...maybe I haven't leak,..but this gasket and the a stud is very old,..and in very bed condition,..and I'm afraid that it will be damaged in moment when I'll be for example 500 km from my house or mechanics, so I want to repair it and put the new gasket and new studs. > If it is the manifold gasket and you do break a stud when attempting to > remove the nut, I know for 100% that the stud will be broken,..because it's very old and it's very thin. So in 100% I must put the new studs and drill and tap the new hole. >then you must drill out the remaining piece of the broken stud, and tap the >hole for a new stud. If you have never used a tap and die set, this would >not be the place to start learning; take it to a mechanic. Yes, I know it,...but the mechanic have to put out the engine or engine's head?? or he can do it (drill and tap the new hole for new stud) without put out the engine's head?? Thanks for all.... SignatureJarek (SQ1EUO) - V740 B230F + LPG (1988) - POLAND sq1euo@wp.pl sq1euo@stud.pam.szczecin.pl GG: 1277234 > Uzytkownik "Andrew McKenna" : > [quoted text clipped - 8 lines] > for example 500 km from my house or mechanics, so I want to repair it and > put the new gasket and new studs. You can drive a very long way with an exhaust leak. In fact, you can drive thousands of kilometres with the exhaust completely removed (not recommended but you can). If it isn't broken, then don't fix it. >>If it is the manifold gasket and you do break a stud when attempting to >>remove the nut, [quoted text clipped - 12 lines] > > Thanks for all.... The rule is that the only stud that will break is the one that is hardest to reach. Theoretically if you have a hoist and you remove the manifold completely, you can replace all of the studs without removing the head or the motor. In reality in a work shop with a sling it might be easier to remove the motor complete. Only in a home garage with no sling or hoist would you need to remove the cylinder head. That would be a big job. SignatureCheers Andrew Uzytkownik "Andrew McKenna" : > The rule is that the only stud that will break is the one that is hardest > to reach. I think,that all studs will be broken in my car,..they're very old and conoded, they're very thin. >Theoretically if you have a hoist and you remove the manifold completely, >you can replace all of the studs without removing the head or the motor. Yes,..but the problem is, that there will be reminders on studs in the engine's head, because they will be broken,....I will have to make new hole and drill it. > In reality in a work shop with a sling it might be easier to remove the > motor complete. Only in a home garage with no sling or hoist would you > need to remove the cylinder head. That would be a big job. I don't know if the mechnics have got special equipment, which can make a hole and drill it in the head, without put out the engine or head. Thanks a lot... SignatureJarek (SQ1EUO) - V740 B230F + LPG (1988) sq1euo@wp.pl sq1euo@stud.pam.szczecin.pl GG: 1277234 |
Reply to this Message |
 Sign In
 Join
 My Latest Posts My Monitored Threads My Blog My Photo Gallery My Profile My Homepage Start New Thread Enable EMail Alerts Rate this Thread
|
©2008 Advenet LLC Privacy Policy - Terms of Use
This website includes both content owned or controlled by Advenet as well as content owned or controlled by third parties.