 |
 | Home | Contact Us | FAQ | Search & Site Map | Link to Us |
 | Sign In | Join | Other 45 Sites in Network |
Car Forum / Volvo Cars / July 2006Idle question on 1987 740 B230F
I've come to believe that a "24 hour" rule exists on my Volvo. It's like I make an adjustment and I don't notice anything. 24 hours later, I start the car and the changes take effect. One example is my idle. I think I am fighting pinhole vacuum leaks and I am trying to isolate them - but here's the deal. I've cleaned my throttle body & IAC and she idles well under the circumstances. But, when I turn the black knob under the throttle body - it doesn't affect the idle - until later in the day when I restart the car, or 24 hours later. By 24 hours I generally mean I let the car sit until the next day. Anyway - let's say my car is idling at about 600 rpm. I open the knob 1/2 turn, then another and another and another and 2-3 turns later the engine is idling exactly the same. I shut the car off, come back a few hours later, or the next day and the idle is up according to the turns. Why the delay? Thanks! > I've come to believe that a "24 hour" rule exists on my Volvo. It's > like I make an adjustment and I don't notice anything. 24 hours later, [quoted text clipped - 18 lines] > > Thanks! I think the difference is warm/cold. The idle adjustment knob controls the minimum amount of idle air, but the electronically controlled Idle Air Control valve should be doing the main adjustment. If the throttle body and idle air control valve need to be cleaned out (as they need every couple years) the cold idle becomes unsteady. Mike Thanks Mike, What throws me is that I thought the purpose of that knob was to speed up or slow down the idle. For example, when I my car is running and I see the idle on the dash around 600 rpm and I want it to be 900 rpm. So I open the hood and turn the knob open until the car idle increases to 900 rpm. Is this not correct? I do recall reading something where I was supposed to disconnect the electronic idle control to set the idle, but didn't quite understand that. I figured that knob was to manually set the idle speed. Is this not so? > > I've come to believe that a "24 hour" rule exists on my Volvo. It's > > like I make an adjustment and I don't notice anything. 24 hours later, [quoted text clipped - 26 lines] > > Mike > Thanks Mike, > What throws me is that I thought the purpose of that knob was to speed [quoted text clipped - 10 lines] > > I figured that knob was to manually set the idle speed. Is this not so? I've never done the electronic disable myself; I understand it is done by grounding one of the wires in a 2-pin connector that is floating around behind the air cleaner. But the electronic part will take over if it can. That screw is a needle valve that controls a passage around the throttle plate, and the electronic control is a valve that does the very same thing. When the screw is adjusted right and the throttle body and IAC valve are clean, the idle will hold steady around 600 rpm as it should. Mike Hmmm. Ok, thanks. It's hovering around 600 rpm, but when I first engage into gear I am getting the dreaded one-time stall. Then there is an intermittant, mild miss I am getting at idle. I recently pulled the throttle body off to clean it, checked the openings and did make sure the idle knob holes were clean. I still think I have some tubes to check for vacuum, and the miss only started after I pulled the plugs and wires off several times to replace the valve shims. I spent a fortune on those Bosch wires so I hate to go replace them know - so we'll see. Thanks again. > > Thanks Mike, > > What throws me is that I thought the purpose of that knob was to speed [quoted text clipped - 22 lines] > > Mike > Hmmm. Ok, thanks. It's hovering around 600 rpm, but when I first engage > into gear I am getting the dreaded one-time stall. [quoted text clipped - 9 lines] > > Thanks again. Stumbling at idle is very often the result of deposits in the throttle body and the Idle Air Control valve. Both are easy enough to remove, and between them it takes about a can of carb cleaner to get the goo out. The critical area in the throttle body seems (to me) to be that passage the black screw controls. The throttle body can be cleaned somewhat in place, washing out the throat with a rag soaked in carb cleaner and spraying it through that idle passage. Mike I did all that Mike. I've already cleaned all of the above very well. The only thing different was that I ran Sea Foam through the system later. I pulled the throttle body again and cleaned it, but not the IAC again. > > Hmmm. Ok, thanks. It's hovering around 600 rpm, but when I first engage > > into gear I am getting the dreaded one-time stall. [quoted text clipped - 19 lines] > > Mike I cleaned the IAC again and checked the vacuum tubes. It seems to be better. I'll test further. thanks, jb > I did all that Mike. I've already cleaned all of the above very well. > The only thing different was that I ran Sea Foam through the system [quoted text clipped - 24 lines] > > > > Mike |
Reply to this Message |
 Sign In
 Join
 My Latest Posts My Monitored Threads My Blog My Photo Gallery My Profile My Homepage Start New Thread Enable EMail Alerts Rate this Thread
|
©2008 Advenet LLC Privacy Policy - Terms of Use
This website includes both content owned or controlled by Advenet as well as content owned or controlled by third parties.