Hi, from some days ago I have some problem when I start the engine o
my Mazda 6 Automatic. When I put the shift in D and accelerate th
car dont run, the transmission slippery. Take around 30 minutes an
no problem. Only when the car is stopped for more than 6 hours. Als

I have a 1989 Mazda RX-7, which over the last few months has occasionally
been hesitant to start. On these occasions it would turn over and fire
immediately, but after about 1 second it would stop - like it was not
getting fuel. When this happened I could rely on this repeating for ...

The Mazda dealer only lists FRONT mud flaps for my 1999 MAZDA 626 LX-V6
4DR sedan, but this car also had REAR mud flaps right from new at the
dealer where I bought it.
I've seen ONE listing for an aftermarket rear mud flap on auto parts web

I have a 1999 miata I am storing for the winter. I want to put in up
on jack stands but I'm not sure where to set the stands.
Can someone help?
Johnnyb

Anyone have any experience with the ScanGuage?  I've been toying with
getting one for a while, and I'm edging closer to it.  (I've already
located the OBDII port it plugs into.)

Last week, I took my 2004 RX-8 to the dealership to replace the sun
visor.  When the service advisor entered my VIN, he found that Mazda's
MSP16 service program applied to my car so they flashed my PCM.  
Afterwards, my car stalled when I stopped for traffic lights.  I

I am considering a purchase of this vehicle - any experiences good or bad?
Not sure which engine yet but it will be automatic.

1996 MPV 3.0 (115k miles) has developed a ticking from what appears to be
the valves.  Oil/filter has been changed every 3500 since new, vehicle
runs great other than ticking.
Sound is heard mostly when engine is cold, but also comes and goes once in

Is Mazda ever going to offer the Mazda 6 with a nice six speed manual
tranny (and with the V6 engine option)?
If Honda and Acura can do it, why not Mazda?
I'm still driving my '99 Mazda 626 LX-V6 with 5 SPD manual for this very

Cut-to-fit hoses. Total crap. I bought them from Autozone(I know, you
may commence insulting me now...) when I was doing the water pump/
timing belt job on my 97 NA. I needed new hoses, the originals were a
little crusty looking and I wanted to drive the car. I noted when I

Heard a weird creaking (no, not the exhaust, haha) as I backed out of my
parking spot. Pulled out onto the highway and all of a sudden there's this
violent oscillation, kinda like you'd get with a bent axle/wheel only felt
like it was up and down as well as side to side... ...

'91 Miata.
The exterior rubber around the windshield, around the door windows and
window wiper blades and door jams.
Getting hard and not very supple over the years.

The exhaust on my 2008 2.0i Sport NC  has really got creaky of late - and by
creaky I mean that as it expands/contracts, you can really hear the darned
thing, even while the engine is still on.  I've never known a noisier steel
exhaust and it's so crazy I wonder if anyone else ...

you might remember my 95  m-ed w/ an eaton s/c has been stalling on
deceluration, (and on start up i discovered),  since i dont have the
sst the factory manual uses to diag issues, i just used my multi
meter.

its getting time for another project and i am thinking of doing a rhd
conversion on a to be obtained miata.  has anyone done this?  i havent
found any detailed sites which discuss a project like this, are there
ones i missed?

All,
When I did the WP, hoses, belts...all that stuff on my 97 a few months
back, I got all my parts from Rock Auto. The valve cover gasket I used
was a "Fel Pro VS50364R".

I saw this site and I like it so much, I'd like to see it to learn a
lot of things
 http://zzrz.com/english.htm

anyone else get this crap via email?
i wont ever buy anything from this spammer
peter