| Thread | Last Post | Replies |
|
| hmmm...very interesting | 02 Mar 2004 23:36 GMT | 1 |
the subjects that show up in vbb must be very old indeed
|
| How much would it cost.... | 02 Mar 2004 22:50 GMT | 9 |
I was thinking of getting something like this done: http://www.wetworksgarage.com/features/boston%20passat/photo13.jpg I already have my equipment, I just need it installed in such a way that I don't loose all my trunk space. From the picture all I want would be the
|
| long ground back to battery | 02 Mar 2004 21:14 GMT | 47 |
I had a new amp installed yesterday (JL 450/4) - my 2nd amp, and since the 1st amp (JL 500/1) was running off 8 gauge wire, they wanted to run 4 gauge. So now I have 2 runs of 4 gauge, 1 to each amp; but he also ran 2 runs of ground back to the battery. I have read numerous
|
| Jenson bandpass ? | 02 Mar 2004 17:25 GMT | 1 |
I may not be at the right group for this question. I'm sure someone here should know though. I have a Jenson Bandpass box with 10" subs with KS on the cones. Anybody know what they are? These are probably real cheap, I don't know.
|
| Car CD Skipping When WARM | 02 Mar 2004 09:48 GMT | 3 |
I just bought a Toyota Echo and am finding my CD player a little frustrating. Here is the problem: When the car is COLD, the CD plays just fine. Usually when I'm driving around town, I don't have a problem with skipping. But
|
| Opinion needed | 02 Mar 2004 08:01 GMT | 1 |
which sub out of a 12" Rockford Fosgate Punch Hx2s and 12" Kicker L7 is best of SPL?
|
| Part of a new "removable" system | 02 Mar 2004 06:11 GMT | 3 |
Anyone have an Infinity BassLink? Do you like it? http://www.sounddomain.com/sku/INFBASSLINK Since getting ripped off I am going to make my system removable(except the satellites).
|
| What size amp should i buy | 02 Mar 2004 03:32 GMT | 4 |
I have 2 JL Auido 10w3d4's. I want to wire them in series/parallel ( i found the instructions on the JL website http://www.jlaudio.com/tutorials/wiring/#2dvcsp ). I want to run 250 watts to each of them. These speakers are dual voice coil 4 ohms. The
|
| DIY problem: Front speakers not working | 02 Mar 2004 02:36 GMT | 5 |
I just purchased a Kenwood MPV622 player for my '88 RX-7 to replace the MPV619 I had stolen a couple of months ago. When I hook the new unit up, everything works except the front speakers. No sound at all from them. I have no amp or disc changer or anything fancy - just a
|
| 1979 CADILLAC SEVILLE: AM/FM/CD deck? | 02 Mar 2004 02:36 GMT | 2 |
Anybody know of a good resource for an AM/FM/CD deck which can be retrofitted into a '79 Cadillac Seville? I live in Minneapolis, and am hoping to find a dealer in my area. If you have any suggestions, kindly post here as a reply or send info to:
|
| 2003 Audi TT Coupe - System advice needed | 02 Mar 2004 01:17 GMT | 2 |
First off, thanks for looking at this post. I can use as much advice as I can handle. I've got a 2003 Audi TT Coupe that I want to do a system upgrade on. I'm keeping the stock HU (for now). My intent is to add a nice amp, a
|
| OT: free webservers? | 02 Mar 2004 01:12 GMT | 17 |
Ok, geocities is stupid. Anybody have any suggestions for a low-traffic free webserver? I don't need anything more than about 20-30MB of space. Ads are ok, as long as they're minimal.
|
| Help - vented enclosure | 02 Mar 2004 01:11 GMT | 1 |
I want to make vented enclosure (48 l) for R-type 1221D subwoofer(Alpine).I heve a little problem - I dont know which dimensions of port should I put in? I was thinking about putting 2 ports - 7,2cm in diameter and about 20cm long.!?-Should that be enough for that enclosure? ...
|
| Fader: Preamp & powered outs | 01 Mar 2004 16:08 GMT | 3 |
So I prewired (hopefully adequately) my van before dropping it off at the conversion shop. From the dash to the mid-rear of the van I ran: two pars of RCAs; pwr, ground, and turn-on; aux input cable; and two sets of speaker wire (which I may not use). I will have front door
|
| correct box size for 10" | 01 Mar 2004 05:56 GMT | 1 |
I can't seem to find the correct volume for my 10" It is in a variable box. At 1.5cuFt it sounds nice but when I make it about half of that it is a bit softer but it sounds about the same. What should I listen for when I size my box? I want it as small as possible.
|