i want to run 4 subs and 2 amps, so 2 subs to each amp.  i have th
correct capacitor, and a power distrobution block and a groun
distrobution block. I have tried over and over again to wire this setu
but have failed so far. if someone could give me a diagram or detaile

I have a Sears 10amp/2amp battery charger that I was thinking about using as
a power inverter for a Radar class I have to teach.  I was going to buy a
cigarette lighter socket adapter with bare leads and use this to hook up to
the pos and neg terminals of the battery charger.  I ...

Okay.  I'm sure you're all just dying to hear me tell you how happy I am
(again) with my new CD player, so without further adoo...
I have NEVER heard so much detail and articulation in my entire life.  All
of my favorite music that I've listened to hundreds of times and know very

As some may know, I purchased a Kenwood Excelon KDC-X789, and this unit has
an intriguing display. You can actually download videos and pictures to the
unit from the Kenwood dispaly site. I've also been informed that you will
soon be able to get a program that alows you to make your ...

I've been thinking about installing a temperature gauge to moniter my
amplifier.  So far the cheapest one I've been able to locate (after
many hours of internet searching) has been a cyberdyne model which,
before shipping and tax, comes out to $67.97 with the gauge and sender.

I've been reading this group, and someone said that the location of
the alarm is very imporant.
I"m guessing that means it shouldn't be under the dash on the left of
the steering wheeel, because that's where everyone puts it.  Is that

The battery on my Nissan Exterra recently died a natural death.
However, after the new one was put in, the radio (and related items
like the clock and CD player) do not come on. It does not appear that
any fuses have blown. Any thoughts? Thanks

ok so the amp is an orion 1200d (725W@2ohm) and the subs are 2 ascendant
audio atlas 15s (wired to 2 ohms).  I was playing with my gains because I
can't really find the point where i get a clipped signal.  If i turn the
head unit up past about 50 (of 62...pioneer p7700mp) i can ...

does anyone have a parts earthquake amp from this series?  I will buy a
few of the fets out of it if you do. IRFZ44 1R 6P mosfets are what I
need.  If you have them i will pay good $ for them.
Thanks!

i have two separate amps hooked up, one for subs and one for 6x9's. th
smaller amp has its own ground, but the power and remote are off of th
other amp. the sub amp is running off of sub preouts, the other of o
the rear outs, not daisy chained. even when i used the high out

I'm putting a Rockford Fosgate 100.2 amp and a Rockford Fosgate 12" sub
in my jeep wrangler to run w/ a JVC head unit.  Since I only have one
speaker, and limited space, I'm going to make a custom speaker box,
probably 14"x14"x10".  The box will go behind the back seat.  That

Just out of curiosity...  When you use a Y-Cable to split a single pair of
RCA outs into 2 pairs of outs, what exactly is being "split"?  In other
words, what are you losing?  Voltage?
Tony

does anyone know where I can find a manual for the above? TIA

I am looking for recommendations on a small amp just for tweeters.  I
have a Sony XM-2020 in another vehicle that is similiar to what I am
looking for, but that is not made anymore.  Any suggestions?

Yes, the Pioneer has MP3, but Naks have good sound quality.
But Naks have reliability issues, but Pioneers need an additional box to
enable AUX in, while it is straight standard on the Nakamichi.
Also Pioneer is ISO, while the NAK would need wiring.