| Thread | Last Post | Replies |
|
| Change/Unchange HU | 22 Aug 2005 10:29 GMT | 1 |
We have seen numerous posts where the factory HU is replaced by an after market one. I need to know since the factory sets blend with the dash, if anybody has experciences in changing the HU but keeping the face of the factory HU.
|
| Newbie question - RMS x 1 @ 4 Ohms | 22 Aug 2005 07:03 GMT | 7 |
I am newbie to this, hope someone can help me. See below... Is Sony more powerful than JL 500/1 @ 2 Ohms regardless of voltage, let's assume both running on 14.4? because Sony can produce 900W RMS, while JL constantly produces 500W RMS???
|
| vw beta radio | 22 Aug 2005 06:45 GMT | 1 |
hi, i just bought a vw passat... got with it a blaupunkt beta radio, with 2x20W question... is there a possibility to connect an external amplifier to the radio, so i
|
| Help with Mazda 626 Bose system | 21 Aug 2005 20:17 GMT | 8 |
I have a 1998 Mazda 626 ES with Factory Bose AM/FM CD system. I got two inches of water in the car and the amp under the passenger seat got soaked. I dried everything out but the sound was now very distorted, with occassional extremely
|
| Need help with audio setup | 21 Aug 2005 02:20 GMT | 2 |
Hey guys, I recently purchased a 02 ford explorer sport track and sinc there's not much room I was wondering if you guys can help me out wit the audio setup. I want something that don't take much space but stil have some knocking. I have $1000 that I can dump into the system
|
| Need good radio antenna ... which? | 20 Aug 2005 19:18 GMT | 2 |
Guys, My motorized antenna is getting a little tired ... am looking for a replacement. Preferably not motorized ... Which is the best type/brand to get?
|
| Wiring an amp | 20 Aug 2005 18:52 GMT | 6 |
I have a Kenwood KFCW-300S Sub that I am connecting to a SPLX SPLA350 Amp using an Autoleads PC4-20 wiring kit. The wiring kit comes with a 15, 20 and 30 Amp Fuse, should I use the 30, 20 or 10 Amp fuse for the amp live from the car battery?
|
| JL Audio 10W7 Question | 20 Aug 2005 03:34 GMT | 3 |
I have an existing amp which can handle 500W RMS at 4 Ohm mono mode, is it powerful enough to feed the JL 10W7 (it says 500W RMS in the spec.)? Will it overwork on my amp? or do I need to upgrade the amp too? Right now, I have one 12" W6V2.. it doesn't sound as good as I ...
|
| Ranting and Raving About the DRZ9255! | 19 Aug 2005 12:20 GMT | 2 |
Just installed my new Clarion DRZ9255 today. Wow. All I can say is this is one FINE head unit!!! I didn't realize you can control both the LP "and" the HP crossover frequencies for each speaker (except the tweets). The Eclipse only let you
|
| Portable cassette player into car CD speakers? | 19 Aug 2005 07:26 GMT | 6 |
Is there a way to plug a portable cassette player into my car speakers? Here is the problem. I only have a CD player in my car. I am trying to listen to stuff on my portable cassette player in the car. Naturally it sounds like crap. Other than earphones, is there some way
|
| How Hot? | 18 Aug 2005 20:17 GMT | 5 |
Hey All! What is the hottest temperature I should expect an amplifier to go into protect mode? I know, I know, there are many factors that can affect this blah blah blah... I'm looking for a maximum temperature
|
| Cell phone mute? | 18 Aug 2005 17:26 GMT | 10 |
I just picked up a Kenwood Excelon KDC-X789, and I was wondering how I would go about using the "cell phone mute" option. I have an Audiovox CDM-8910 cell phone, and all I know is that there is a single "Phone Mute" wire in the rear of the head unit. Any help?
|
| Car ALARMS DEI Radar Sensor 508T | 18 Aug 2005 15:58 GMT | 8 |
1) I have a Directed Electronics Radar Sensor 508T and I don't understand all of the instructions. I have two versions of the same sensor, made several years apart, and I just never got around to installing either before.
|
| Help with a Jensen Amp | 18 Aug 2005 13:34 GMT | 5 |
I have a Jensen XA 6040LX that I bought new years ago. I now want to hook a subwoofer up to it, but I can't find the manual. Does anyone know how to do this? I currently have four full range speakers connected, but I know it'll
|
| JL Audio 10W7 Question | 18 Aug 2005 08:17 GMT | 3 |
I have an existing amp which can handle 500W RMS at 4 Ohm mono mode, is it powerful enough to feed the JL 10W7 (it says 500W RMS in the spec.)? Will it overwork on my amp? or do I need to upgrade the amp too? Right now, I have one 12" W6V2.. it doesn't sound as good as I expected ...
|