I have a 1991 Geo Prizm.  When I hit my left turn signal, I hear a loud
screech that does not stop until I either turn the turn signal off or
hold it down hard.   When all I hear is the screeching noise, neither
the front nor the rear turn signal lights blink at all.  However, when

Heh, hold back the flames, plz, and read this one:
http://www.thisismoney.co.uk/money-savers/article.html?in_article_id=403819&in_p
age_id=5
Another company claiming to boost combustion efficiency by injecting H2
into the fuel mixture. This concept claims that hydrogen will be

I just had the second blower voltage divider fail on my van, and thought I
would post about
this.
This divider provides the multiple fan speeds, and is installed in the air

Have a friend's 86 Ford Bronco II sitting here.  The clutch takes hold at
the very top of the stroke of the pedal.  Is this normal?  There is no
adjust at the master cylinder end and the slave cylinder appears to be
inside the bell housing...  The clutch does not appear to slip.

I'm thinking about trying it.  22r block with a 20r head. Has any one
done this?    I will be building the motor for a 81 2wd standard cab
truck.  This is still on the drawing board.  Just kind of kicking the
idea around.

I've had SilverStar H1's in my low and high beams for almost 3 months. Well,
yesterday my left low beam quit. My original stock H1's were good at 2-1/2
years of use. Fortunately PepBoys has a 3 month guarantee and gave me a pair
of new SilverStars.

I'm replacing the ball joints (and control arm bushings) on my Grand
Am... do I need to pack any grease into the ball joint area before I put
the rubber boot and install it on the car?

HELLO, I AM NEW TO YOUR SITE, I HAVE READ SEVERAL POSTS W/SAME PROBLEM, BUT
I NEED FURTHER ASSISTANCE. I REPLACED THE COMPUTER BRAIN, THE FUEL PUMP AND
FILTER, REMOVED BOTH INJECTORS CLEANED REPLACED GASKETS/ORINGS, HAD THE
IGNITION MOD TESTED/PASSED TESTED THE PRESSURE TO FUEL PUMP ...

anyone know where to find a gas tank for 2008 Lexus Minority report? Thanks

How difficult is replacing the bottom hinge on a 1982 Crown Victoria? They
are just bolted not 'glued' on correct?
Thanks

IF I TAKE MY HEADS IN AND GET A VALVE JOB CAN I GET SOME MORE POWER LIKE
GETTING BIGGER VALVES INSTALLED AND POLISHED UP PORTS AND STUFF OR IS IT A
WASTE OF TIME WILL I GAIN 20-25 HORSEPOWER THAT WAY OR IS IT ALL WITH THE
ALUM. HEADS THE WAY TO GO?

I have a leaky radiator that I need to dispose of.  Seems like a shame to put
so much metal in the dumpster.  Should I take it to a radiator shop?  Recycling
center?  Or just ignore my feelings on the matter and trash it? :-)  I can't
think of anything else I could possibly put it ...

I have a 96 beretta v6 3100 that has a knocking noice in the engine and the
tappets are rattling. is this a sign of a cut bearing and how bad is the
oil pan to remove from this thing?

Got a '90 Mercury Cougar and it's time to replace the fron brake pads.
When the Ford dealer replaces the pads I get MUCH LESS DUSTING on my
mag wheels. When independants do the brakes I get MUCH MORE DUSTING.
Does anyone know of a good replacement besides the O.E.M. Ford pads.

Check out this Snap-On Scanner plus cartridges, case, manuals, and
connectors. Very nice if you own your own shop. There is only a few hours
left on this auction. If interested, take a look.
Thanks for your time,