Somebody gave me this car. It just gave out on them. A mechanic told
the person that the timing belt probably slipped some teeth. The
mechanic said that they lost spark and installed a new distributor and
had spark again and it still wouldn't start... I am not getting any

could some kind soul recommend a place to buy a reverse distance sensor?
what brand?
assume location US
am driving a longbed truck and finding it difficult to estimate when rear

And a few generic questions I have for the gang.
First, my good ole' alignment shop nailed the problem. No bearings or
bent axles - just a left rear to they said was "waaaaaay out".
Specifically, it was -0.68 deg.  Spec is .10 to .20 degrees on both

i have a 1991 lebaron that was running fine but then started running
sluggish like it was trying to stall out while driving.. i am thinking
it is a clogged fuel filter .. any suggestions

I would appreciate some information on how to repair a crack in the
frame of a VW Cabriolet. I understand this car has unibody
construction. The crack simply appeared, there was no accident or
impact.

hey everyone, i have a 69 camaro with a 350 in it.. i have done alot of
work to it, building it from the block up. it is a four bolt main,
bored 40 over with high compresion- 10.5:1. it has a set of fuelly
double humper heads with a 190 intake valve. also it has a wild comp

99 Nissan Maxima w/3.0L EFI and automatic, 135k miles.  It
was started and move from garage so kids could play while
raining.  Started easily and ran well to bring back into
garage.  Next day, it cranks as it should but, won't start.

Grabbed a BlueHeat brochure tonight at the Toronto Auto Show. It appears to
be a small gas powered heater that is installed in your vehicle so that it
provides near instant heat and engine warm up.  Anybody out there heard
and/or has experience of it?

I have a '90 Jeep Cherokee that won't start. When I turn the key to the
"start" position, nothing happens except for the temp. gauge needle
goes all the way to the right. The battery tests at 12.5V, and there is
no "click" from the starter. I tested the voltage at the ignition wire

I came across this dual coil and dual ignition module kit. The price is
around a thousand dollar. This sound way too expensive. I want to build
one for my own vehicle but I not sure if the secondary output of the two
coils should be tied together. For instance, if I tie the ...

i have a 93 toyota 100 with a 3 ltr engine that has no spark, no
injector pulse, and keeps setting a code 12. i have tried coils, ecm's,
igniters, distributors all to no avail. i have checked wiring for
proper power and grounds all ok.also tried new relays to no avail. now

So from what I hear, DOT specifications have restrictions on the output
and allowable power consumption by each lamp type.
If the 3,000 lumen HIDs are given the ok, why wouldn't an adequately
cooled, 150W incandescent lamp be allowed for headlamp use?  

Hi group - I have posted to another group this trouble we are having
with our church van .... be low are the symptoms and also what has been
changed ..
1986 Dodge B150 V8   8.25 rear axle

I have an 87 dodge dakota 3.9L V6.
I just got the E.G.R. valve changed and need to get the smog pump
replaced because of a horrible noise that it's making.  If I take out
the smog pump will that have an effect on the gas mileage?  I ran it

This is probably a very dumb question but I can't find instructions on
the web on how to install an ingnition switch in an older GM vehicle. I
have a 1965 Impala SS with the ignition on the dash. There are 4
connections but I'm not sure where the wires are supposed to be