| Thread | Last Post | Replies |
|
| engine management light showing on vauxall corsa | 06 Sep 2006 15:32 GMT | 5 |
hey i got my engine management light showing on my vauxall corsa its a 1 litre 12v club, and i had it checked out in the garage and they found the following fault codes p170, p300, and p302 and they advised me to replace the air intake ducting which i did, but the light is still on,
|
| AIR BOX! | 06 Sep 2006 14:54 GMT | 3 |
I need an air box for a 2001 Crown vic...everyone says a boneyard/salvage yard...but i cant find any places around here, never the less have the part..Can anyone offer a site for it, or a direct conenciton to a place THANKS! also, i have fuel stablilizer and quoting
|
| Pressing in axle studs?? | 06 Sep 2006 13:59 GMT | 4 |
I just drilled out the axle hubs to 49/64ths. Now am going to press in the new 5/8" studs for racing. Question is: do I lubricate the serrations on the studs before pressing them into the holes? If so, with what? Or do I do it dry?
|
| 1997 Chrysler Sebring Convertible | 06 Sep 2006 13:23 GMT | 2 |
I've posted here before and you guys have been more than helpful in each instance! I was wondering if you might be able to come through for me again?! Over this past week I've had a belt get really noisy on me (I'm
|
| Fuel leaking from the purge canister | 06 Sep 2006 06:37 GMT | 1 |
Hi, my car is 1993 corolla. After driving a while, a lot of fuel is leaking from the purge canister, and it stops leaking when I open the gas tank cap. I can drive with loosing the cap and there is no leaking happen again.
|
| Fuel Injectors? | 06 Sep 2006 01:47 GMT | 6 |
2001 crown vic 4.6...suspect fuel injectors are leaking fuel into the cylinders when sitting. How do i go about checking this problem?
|
| 4 cylinder valve adjustment | 06 Sep 2006 01:39 GMT | 1 |
adjusting valves on a 4cyl, kubota engine. just want someone to verify my procedure
|
| 1996 Monte Carlo Engine Misfiring ??? | 06 Sep 2006 01:21 GMT | 2 |
Got a 1996 Monte Carlo with a 3.1 engine. Sometimes when starting the engine it is hard to start and when it does it runs real rough. After a few minutes it snaps out of it and runs fine. The check engine like comes on so I took it to AutoZone to check the trouble code. The code ...
|
| Installed Cold Air Intake | 05 Sep 2006 23:24 GMT | 16 |
I installed a K&N FIPK last night on my 04 silverado. It seems to be working great. But now my A/C is blowing really hot air. I followed the instructions, so i am not sure what i missed. Can anyone help me?
|
| dead battery | 05 Sep 2006 23:07 GMT | 35 |
this is dumb but... I left my lights on overnight now my car won't start. Dead battery I know. This battery is less then a year old and I am told that if i leave it alone for a few hours it might come back to life. Is that
|
| Rebuilt or new engine replacement? | 05 Sep 2006 20:10 GMT | 16 |
The 350 cubic inch engine is blown in my 1993 Chevy 1/2 ton pickup. Should I put a new engine in, or should I have the damaged one rebuilt? I would appreciate your opinion and/or experience. Thanks.
|
| 4bbl carb disable the secondaries | 05 Sep 2006 15:49 GMT | 16 |
I would like to disable the secondaries on the 1979 Chevy 4bbl carb. I have not found any information on how it's done. I looked at the carb and saw linkage coming from the vacuum diaphargm going to the secondaries. Is this the linkage?
|
| RWD stick shift "family" car... and fairly recent? | 05 Sep 2006 15:21 GMT | 107 |
I give up. Kid #2 is on the way... so I'm car shopping. I don't want a minivan, and neither does the wife. However, her Beretta is 16 years old, my Jimmy is dead, the truck is a regular cab, and the
|
| Problem starting when lukewarm | 05 Sep 2006 15:14 GMT | 6 |
I have a Del Sol (Honda Civic) Si. It has no problem starting when the engine is hot or cold, but in between sometimes just doesn't work. For example, the other day I started it cold and drove 2 miles to a gas station. After filling up, the car wouldn't restart. It cranked over ...
|
| Question about power steering hose | 05 Sep 2006 14:18 GMT | 7 |
My 1978 Ford pickup has a power steering hose that is made of aluminum with a short length of rubber hose between the aluminum parts. The aluminum part that screws onto the power steering pump has a crack and leaks right where the end is "flared" out. It this the kind of thing that ...
|