| Thread | Last Post | Replies |
|
| "Corvette's appeal is its excellence" | 07 Apr 2007 23:38 GMT | 6 |
Corvette's appeal is its excellence Has there ever been a more prolific, more enduring or more successful halo vehicle than the Chevrolet Corvette? at http://www.washtimes.com/autoweekend/20070329-103904-7280r.htm
|
| 1988 Corvette | 07 Apr 2007 19:50 GMT | 4 |
I just purchased this corvette from a private owner. This is my first corvette and I have a couple inquires and a few issues with it. 1).Exactly how does this 4+3 Manuel trans. work? 2).I need to get a manuel book for this year?
|
| Overdrive on and off 1984 stick | 06 Apr 2007 20:04 GMT | 1 |
I have a 1984 4 speed stick. When the overdrive switch is on, it goes on and off. There seems to be no pattern, it is just random. I don't hear any unusual noise nor does the coolant temperture matter. I checked the relay wires and they look ok. Any suggestions?
|
| i wanna buy a corvette | 06 Apr 2007 20:02 GMT | 9 |
hi everyone .. does anyone have any idea about a C6 corvette for sell ??!! i'm trying to find one between $30000 to $33000 manual gear
|
| Simplest question ever... | 06 Apr 2007 15:41 GMT | 13 |
but then again, I've got a simple mind! On a 1994 Corvette convertible where are the turn signal and 4-way flasher relays located? The turn signals on my girlfriends car are intermittently OK, then slow, then OK again so I'm suspecting that the
|
| Sold my vette. Need help as to a good sports or luxure car under $20k | 06 Apr 2007 02:57 GMT | 7 |
Wha is a good clasy or sport car under 20k?
 Signature My love of cars brings me here, Love, the Car Guy
|
| c6 carfax | 05 Apr 2007 05:48 GMT | 3 |
I went to look at a c6 today a 05 with 15k. Price 36,000 Lots of options. 6 spd I noticed a piece of the nose, next to the light was out of line a little. I looked closer and noticed the clip needs to be replaced,
|
| C5 Z06 Seats | 04 Apr 2007 19:20 GMT | 1 |
Although they look nice, I'm not happy with my 2004 Z06's seats. They aren't comfortable. And they don't wrap around much to hold you in in a hard turn. Anyone got any experience with aftermarket seats? Ricarro comes to mind.
|
| C4 Windshield Wipers | 04 Apr 2007 18:41 GMT | 7 |
I have a 1990 C4 Corvette and the windshield wipers hit the hood. I have tried several different brands to no avail. Any ideas?????
|
| C4 Power Increase Suggestions | 04 Apr 2007 01:11 GMT | 3 |
Gentlemen. I have a 1993 Convt C4 "Black Rose" 6 speed with 15k miles. I love the car and plan to keep it for quite a while. It is totally stock. If I wanted more horsepower, meaner exhaust note and better brakes what would you suggest. I took the car around Road America ...
|
| Diminished Value????? | 03 Apr 2007 19:53 GMT | 8 |
I didn't know you could collect for the reduced market value of your car after an accident repair, but the articles at www.claimsreporter.com say you can. I know most people will not buy a car with a bad Carfax unless it's offered at a big discount. Anyone else know about this ...
|
| 12522961 Convertible Conversion Kit | 03 Apr 2007 12:29 GMT | 2 |
Does anyone have any idea where to get a GM part #12522961 Kit. This allows you to install a Glass rear window convertible top on a 1990 Corvette. Please e-mail me if you have one or know of anybody that does have one. Thanks bwegner@machlink.com
|
| 78 automatic rear transmission seal leak | 02 Apr 2007 18:09 GMT | 2 |
I have a 78 with an automatic transmission. The rear transmission seal is leaking a bit and was wondering what the typical cost is to replace the rear seal and-or if this is something I could do myself? I do not have a lift but do have some floor jacks.
|
| "Total Loss" lowballing 1127 | 01 Apr 2007 18:21 GMT | 3 |
Apparently, insurance company repairs as well as 'total loss' claims are lowballed as a general practice. I just read an article at www.claimsreporter.com that says that you can get on average, the ~$2K difference needed to get a replacement ride (vs. trade-in)... for sure, if ...
|
| Pilot bearing | 01 Apr 2007 01:26 GMT | 1 |
Has anybody ever had a new pilot bearing that was too tight on the tranny input shaft? Or can it be too tight if it is installed? It's in a '69 350. Thanks for any help. Steve
|