DANA 44 front axle: $20.00
Gas: On way home from work, $0.00
DANA 60 Rear axle: $80.00
Rear floor for a Blazer from the 6" rise back including tail pan: $225.00

My 97 K1500 has developed a squeak in the rear end.  I think it might be
drive-shaft, universal, or rear pumpkin related, definitely not breaks.
It's very pronounced at low speeds and comes from the rear of the truck.
Any help is greatly appreciated!

i have a 1987 gmc 1/2 ton 4x4 w/ a 305 TBI. sometimes when ever i put the
truck in reverse, or i slow down and stop , the trck dies on me.  it also
does it if im sitting at a stop light and the truck idles. the weirdest
thimg that happened was when it died on me , i craked it over ...

Its time to change the brakes pads on my 97 Jimmy.  I figure I'll give it a
try and save a few bucks.  It looks as if a special tool is need to remove
the hubs.  Before I start beating on them, I figured I better find out
first.  Any online sites that show how to do a rear brake ...

I'd like to hook up a vacuum gauge to the intake manifold of a 1997
chevy 3/4 ton 4-wheel drive pickup with a 5.7 L engine but it doesn't
seem to have any  port through which to do this. It is a two-piece
manifold, the upper portion being plastic on top of which is the

Only a 2WD but someone might help...
'87 chevy pickup C10 (old body style), V6, TBI, TH400 Transmission.  Low
mileage truck... 95K Km (60K miles?).
Things seemed to be fine (I've only had the truck a month) till I floored it

I have a 1985 S10 Blazer 4 wheel drive 2.8 engine and it runs great as long
as the temperature gauge is below 210, but as soon as I get stuck in traffic
or on really hot hot days it seems like I'm not able to accelerate as fast
as I normally can, as if the trany is slipping or maybe ...

Hope someone out there can tell me something about this situation - I'm
getting no help from GM.  Sorry for the long post, but the details may be
important.
Here's the story.  I've got a '96 1500K, 5 speed, 4.3l V6.  For a few years

I fixed mine, my dad's truck has the same problem.  The wipers are
unpredictable and erratic.  I remeber reading a procedure to repair the
problem without buying a new board.  Can somedirect me to that?  I have been
unable to locate it.

I replaced the speed senor on the transmission and this did not fix the
speedometer.  What should I check next?

I'm debating on putting headers on my 1994 GMC K1500, 350 w/TBI.  Right now,
all is stock.  Right now, I have a crossover on my stock manifold that
connects to a single-in/single-out catalytic converter.   From the converter
on back is 3" single exhaust.  Not interested in going to ...

G30 Sportsvan, full floating rearend, 8 lugnuts.
There is a small clicking sound in the right rear bearing so I decided
to research it. But.. the brakedrum is stuck behind the drumpads.
According to my friend Haynes I have to backup the adjuster to release

I own a 01 Silverado (2wd, 4.8L auto). I'm about 2 months from the
3year/36,000 miles ending of the original warranty. I'm pondering
about getting an extended warranty. Any suggestions for the best deal?
Thanks

Quick question (I'll spare you the long story). Would overtorquing the axle
nut on the front hub/bearing assembly on a 4wd S-series damage the bearing?
Spec is 183-185 ft/lbs.

I have a strange problem with my '97 K1500.  On  occasion the
windshield wipers fail to work when turned on.  Neither the wipers nor
the windshield sprayer will function, though I can hear a motor
running when the "wash" button is depressed.  The problem always