| Thread | Last Post | Replies |
|
| Pros/Cons of using Duramix Adhesive (4176) | 11 Mar 2005 04:45 GMT | 1 |
Any yeahs or nays on using: DURAMIX 4176 METAL PANEL ADHESIVE for attaching rust repair panels. I posted awhile ago about mig welding them on, but now I think I will weld the invisible hard to reach areas and get some of that adhesive
|
| Which old truck or car had an aluminum block & head V8 or V6 engine? | 11 Mar 2005 04:40 GMT | 31 |
Designing a new project and I need a light weight engine in a V style. I seem to recall that Buick offered a aluminum block and head V8 a few years back. A V6 would do. Anybody know a older car that I could pick up cheap that would
|
| Transmission Noise | 11 Mar 2005 04:35 GMT | 1 |
I have a 98 Silverado 1/2 ton, I was checking my u joints this morning and while I was spinning the drive shaft by hand I could here a rubbing sound coming from the tail end of the transmission, I thought it might be the center bearing but I am pretty sure it is coming from the ...
|
| Service 4wd Light | 11 Mar 2005 02:30 GMT | 10 |
I have a 2000 Silverado and the service 4wd light comes on and off periodically in the message center. Before going to the stealership and paying for a diagnostic has anyone else had this light come on? Thanks
|
| Chevy Venture | 10 Mar 2005 21:34 GMT | 1 |
I just bought a 97 Chevy Venture and my 30 day tags expired and I still havent recieved the title! I called the dealer and he said he would get it that day and would call when he did but he never called me and now I cannot drive the vehicle! What can I do???
|
| 93 silverado | 10 Mar 2005 14:01 GMT | 7 |
93 silverado 350 auto once in a while, the service engine soon light comes on, stays on for a minute or so and then goes off again. I won't see this for another
|
| problem with turn signal & brake light | 10 Mar 2005 06:47 GMT | 1 |
98 K1500. Fast right turn signal, front blinks fast, rear has nothing and no brake light (right side only). Replaced bulb, problem still there. Fuses seem ok. What else can I look for? Thanks
|
| 2000 Blazer Starting Trouble | 10 Mar 2005 06:31 GMT | 1 |
Have a Blazer with a problem.Most of the time it starts and runs fine but every once in a while it gives grief. Cranks,catches,and stalls. The only way to get it started is to let it sit for about 15 minutes and it fires right up. Any hints would be appreciated.
|
| mirror size matters | 10 Mar 2005 04:39 GMT | 4 |
The mirrors on my 1984 S-10 are too small, in my opinion. Does someone know of direct bolt in replacements that are bigger ? Thanks for your time Felix
|
| 93 350 no-start | 10 Mar 2005 01:56 GMT | 6 |
Working on a 93 K1500 Suburban (350). I have a no-start condition. Have run compression test, over-hauled the distributor, new plugs, cap, and rotor. Installed new fuel pump, and pcm. Engine will only start after distributor is advanced at least 18 degrees. Have pulled timing gear ...
|
| hydraulic lifters tapping at highway speed | 10 Mar 2005 01:55 GMT | 6 |
I?ve got a 95 5.7 L Chevy Box truck (FI), only about 50k miles Runs great all day on local roads, but as soon as it?s on the highway (over 55 mph) for a few minutes, the lifters atart to rattle. There is no drop in oil pressure, and the oil I?ve changed the oil
|
| 1998 Chevy Blazer Keyless Entry | 10 Mar 2005 01:23 GMT | 5 |
I just bought a 98 Blazer, and was wondering if there was a way to tell if it has keyless entry (I did not receive ant remotes), because I was thinking of having an aftermarket alarm & keyless entry system installed. If it has keyless entry, is it possible to get replacement ...
|
| 1968 Ford 250 Truck | 09 Mar 2005 21:20 GMT | 3 |
Anyone know where I can find body parts for Ford 360? Thanks, Justin
|
| please help | 09 Mar 2005 21:10 GMT | 5 |
I have a 95 gmc 1500 truck with a 350 5 speed. The problem is when idling or running at low speeds when i accelerate i can hear coolant running or sloshing through the heater core. It isnt running hot or missing any. It is annoying ang i would like to try
|
| off topic, jeff topping insults in this NG | 08 Mar 2005 17:18 GMT | 1 |
This dude is a real trouble maker. Has anyone else had problems with him. Email responds.
|