ok I took my mini van to the shop and they said it was my torque converter.
so they unhooked my overdrive will that damage my tranny? or anything else?
they also told me I was looking at over 350 dollars in repair for the
torque converter is that reasonable or should I go else ...

Thinking I'd like a Stepside but have a fairly nice '87 Fleetside.  Any
thoughts on how tough a project this would be?  Of course the Fleetside is a
'longbox'.  Was there a 'longbox stepside'?
The stepside did exist in '87 but I don't know if there was a longbox

I own a 1991 Silverado ext. cab.  When I switch to defrost position, the
display begins to flash and the defrost doesn't work.  If I set the position
to half defrost/half floor it appears to work fine.  Any suggestions would
be greatly appreciated.

any tips?  I know this is going to suck.  No water in the oil, it's leaking
to the outside. 86,000 miles on it any thing I should change while I have it
all apart?  I'm thinking a full day to do it and I would like to wait until
memorial day weekend and just watch the coolant level.

 75% of the post here are on S10`s.
Are they crap? They must be.
Never seen so many problems.

Where is the turn signal flasher located on a 1995 Chevy S10 Blazer?
Thanks

My husband just bought a 1988 Chev Silverado Stepside with no owners manual
at all, so we're hoping someone can tell up how to set the clock on the
factory installed AC Delco radio.
Thanks for any help.

I have a 1998 GMC 1500 with the 5.0L V8, for its age it has low milage...
just over 54k.  However it is having a few problems growing old, a few of
which I can handle fine myself, and one biggie that I am going to get help
with.  Over the last few months been noticing a very slow ...

I have the shop manual and the wiring manual, but can't seem to figure
out where to connect the signal wire for the tach.
It's an ignition tach, instructions say to connect to the coil
negative.

My husband has a 94 chevy 1500 4X4 ex-tend cab 5 speed truck. It is
making a wierd noise (rattling type) when you shift into the higher
gears and when you are going a certain speed. He thinks it may be a
bearing going out in the rear-end. The u-joints were both just changed

My rear wiper stopped working a while ago on my Blazer.  Took it to the
dealer, they said I need a new motor and the repair would be over $500!
For that price, I'm willing to try and fix it on my own.  Does anyone
have any experience doing this?  Is there a site/guide I can pick up ...

I have a 79 GMC 1/2 ton pickup with a 250 straight six that I purchased a
while back for my son as a project. I was told by the previous owner that
the truck wasn't driven for at least a year and was only started once or
twice during that time. The engine runs rough, but doesn't ...

Howdy
Can anyone recommend a repair manual ?
I just bought a 2002 S-10 LS  4cyl 5 speed.
Need to check everything out on it.

I bought a 1973 chevy truck 3 months ago and have gone though 3 starters!
Thats a starter a MONTH! The start makes a wired noise like 3 days b4 it
goes out(locks up). High pich grinding noise(?) i think internal
short-cirrciut(?), How can i fix this/these problem(s)? ASAP -  Repond

F/S removable top off my '89 Fullsize GMC Jimmy. Sliding tinted glass
and factory Air Deflector, Black w/white interior. NY 845 area code
Orange/Rockland. You must pickup the Jimmy is dead.