| Thread | Last Post | Replies |
|
| 51chevy p/u frame mod or swap | 03 Apr 2005 04:13 GMT | 1 |
need help+advice mod the org frame or switch to S10 frame?
|
| Fabtech vs RCD | 03 Apr 2005 03:29 GMT | 1 |
I've been looking at lift kits for my 03 silverado so I've heard that fabtech and RCD are the best out there but I have looked into iboth and RCD looks to be a better product and they include bilstein shocks in the kit, but they only offer 6" lifts
|
| 2000 Blazer - no heat to the floor | 03 Apr 2005 03:29 GMT | 1 |
Looking for some advice here...I don't get any air flow to the floor when the control is set to the floor, it is deflected to the defroster. I get air flow out of the dash vents when switched to the vent position. I am guessing it is a vacuum problem, but haven't got a clue where ...
|
| Why won't my 1991 K2500 Silverado Won't start | 02 Apr 2005 21:42 GMT | 3 |
My truck cranks over just fine but right after its done cranking it just dies. Its a TBI injected 5.7l 350 with only about 12,000 miles. The fuel pump is only 6 months old. I'm thinking its a sensor but I'm not sure which one controls the fuel to the engine and creates the idle.
|
| Want to Buy.. Door Locks/ Jam parts on door 92Z71 | 02 Apr 2005 05:29 GMT | 1 |
When I close the Door it will not always catch. Sometimes I have to take a screwdriver and press down the catch on the door.. I notice there is 3 screws holding it on... What is the part called, how is it installed and were can I get one for my 92 Z71 Driver Door...
|
| dexcool, or not dexcool? | 02 Apr 2005 05:08 GMT | 12 |
What are opinions or dexcool; leave it in, or change to green variety?
|
| My truck doesn't start unless... | 02 Apr 2005 05:03 GMT | 4 |
I have a 1995, S10, 4.3 engine, manual trasnmission and the problem I'm having is that it doesn't start unless I put a little bit of gas in the place where the injectors go. If I put a little bit of gas there the truck starts and no problema after that unless I turn it off and
|
| 98 truck | 02 Apr 2005 04:43 GMT | 2 |
I have a 98 V8 454 Chevy truck and the check engine light is on. I got a code reader. It shows a code PO171, system too lean , bank 1. Does anyone I any ideas what it could be? Thank you for your help,
|
| "99 Fuel Gauge | 01 Apr 2005 22:36 GMT | 3 |
1999 Silverado, Z71, 5.3, Stepside, 101,400 miles. Problem with fuel gauge after filling tank. Occasionally the fuel gauge will go to "E" and "Low Fuel" warning light will come on. Shifting to "neutral" and rev RPM's OR turning off the ignition and back on, will
|
| A Sad Day for the Silverado....... | 01 Apr 2005 16:00 GMT | 19 |
Yes, tis a sad day here in Minnesota..... You may have read my earlier posts extolling the virtues of the 2005 Chevrolet Silverado 2500HD diesel crew cab we purchased... I have claimed, IN THE PAST, that of the vehicles I've owned in the past 40 years this is the most perfect...
|
| Help 98 truck | 01 Apr 2005 07:04 GMT | 1 |
I have a 98 V8 454 Chevy truck and the check engine light is on. I got a code reader. It shows a code PO171, system too lean , bank 1. Does anyone I any ideas what it could be? Thank you for your help,
|
| Chevy jerking/jumping on the highway | 01 Apr 2005 06:56 GMT | 2 |
Please forgive me as I could not find an active Chevy Auto usenet group. For what it's worth, I own a Chevy S10 truck but this question is about my friend's Chevy Barretta that's giving her some problems. I tried the rec.autos.misc but nobody
|
| Napa Gold Allison Spin-On # 7701 | 01 Apr 2005 02:44 GMT | 2 |
Has anyone notice that the holes around the original equipment Allison spin on filter (part # 29539579) are in a position that you can see the holes when the filter is removed from the tranny - with the magnet still in place? The Napa replacement part is # 7701. After pouring some ...
|
| Leer cap repair | 01 Apr 2005 02:39 GMT | 8 |
I just bought a 1995 Silverado Z71 Extended Cab with matching Leer cap and the pneumatic arms that hold the glass door up on the back of the cap are worn out and I need to replace them.I went to the Leer website and all I got was directions to a dealer 2 hours away and they are ...
|
| 1972 C-20, sell or restore? what am I getting into? | 01 Apr 2005 02:35 GMT | 6 |
I have a 1972 c-20 that I am not sure if I want to sell it or restore it. I am the first owner, had the motor bored out (about 15 years ago) to 30 over, and a few other things done. Still have the factory paint, but rust is now a major problem along the rocker area etc. Looking ...
|