My mother has an old 92 Chevy Blazer that she drives around town in.
She informed me that she has no dash board lights. I thought it was
just a fuse, I pulled each one out and they were all okay.
Its a 92 Chevy Blazer and the dash board is all electronics, my mother

I have a 2004 Tahoe and the transmission has a low whine constantly, but
that is much more noticeable at lower speeds when wind noise is lower.
The transmission also shudders when shifting from 1st to 2nd and is
otherwise jerky.  Is this typical behavior in a Tahoe?

Anyone out there know how to get the trouble code on a 1988 Chevy P/U that
has the "Service Engine Soon" light illuminated?  The manual says to use the
special GM gadget.
thanks

I am moving to Alaska and after much research have decided to buy a
Suburban.  Now I am trying to decide between a 98-99 for appx $9000 or a
01-02 for appx $16000.  Any input would be greatly appreciated!  
Thanks!

I have a 2002 Silverado with 23,000.  This morning when I started
driving the truck and reached 30-40 mph it made a loud clicking sound
upon acceleration ( coming from the area of the gas pedal )    When I
took my foot off the accelerator the sound stopped.  It did this for

I am the original owner and have been driving it since 1979.  Just a
straight six.  Anyway just recentley a problem arose. Manual
Transmission by the may.  The problem is this.  The choke lite comes
on and the air conditioner stops. Then a little while later the the

Well... I guess it's a good thing that I'm about to buy a 14-bolt...
I had mentioned in a previous post that I hit the brakes and it made a
crazy "Brrrrrr!!!!" noise accompanied by a wicked shimmy.  Looking
back, I braked around a turn when that happened.

 I have heard some negative talk about the 6.0 but nothing has really
been said specific.I have a 2500 HD 6.0 w/ 11,000 miles.I'm just wonder
what problems I might get to look forward to.Present or future.
Thanks

For a bit my jimmy would slow down as it turned and the front tires would
peel out. So i tried to widen my turns, but it still did it. A bit later,
i got new front brakes. For a week it was not slowing down as i turned nor
was it peeling out. Today, it started to slown as i turned ...

Ok... I've determined that my K5 was equipped with the GU80 locker from
the factory....  BTW, it's got 10-bolt axles, 3.08 gears, and was made
in 1986.
Since I'm in the process of getting a 14 bolt to go back there I don't

The driver's side wiper arm shifts left and off the windshield when I
use the wipers. It feels like some teeth stripped out when I move it
back. Anyone know what is causing this and how to fix it?
Thanx

I've removed the intake manifold on my 89 Suburban 5.7L, 96k mi, to
try and fix a coolant leak. Coolant is disappearing from the cooling
system and showing up in the oil (about 1qt/3000mi).
Last year I changed the intake manifold gasket for similar reasons. At

How ya been bro..?
The stroker is done, pushing close to 500HP w/o the nitrous...........
frickin handul of power, no doubt !
Just wanted to say hey, you can find me at coloradok5.com

I have my new master cylinder installed and it's been bench bleed and ready to
go. My only problem is I need an "assistant" to help in bleeding the lines and
remainder of the system. I live out in the boonies all by my lonesome and really
have no help to accomplish this tremendous ...

has anyone had this problem.?
i just put together a small block 400 with alum heads and about 9.5 to 1
compression.with a isky 266 cam and anti pump up lifters. new edelblock 650
carb ,stock points type dist. and edelblock esp intake.the coil is a stock