| Thread | Last Post | Replies |
|
| How many splines in my 10 bolt??? | 22 Aug 2005 22:32 GMT | 3 |
Ok... I still have an unresolved rear end issue. The 14 bolt is of course the best option, but it's a logistical nightmare in comparison to fixing the 10 bolt. I'm not in a position to go off road a lot right now, and since this is my daily driver I'm
|
| funny 02 'burb smell | 22 Aug 2005 14:55 GMT | 5 |
Hello - My suburban has a funny smell. It smells like oil on the exhaust manifold. There is no smoke, no noticeable leaks, no oil consumption. Nothing funny in oil. Nothing funny in coolant. Breaks are fine, no squealing. Trans fluid level is where it should be as well. Temp ...
|
| 86 Van 5.0L runon aka diesels | 22 Aug 2005 05:35 GMT | 5 |
Howdy All Damn bugger will not stop! I shut the switch off and it just runs on and on. It scares the hell out of my wife. Almost made her late for work this morning, waiting for the Van to stop running. Running higher octane
|
| Day Lamps replacement | 21 Aug 2005 23:14 GMT | 2 |
On a 2001 1500 burb how do I replace the day lamps?
|
| Horn on 98 S 10 | 21 Aug 2005 22:25 GMT | 1 |
I have a two wheel drive Chevy S 10, 1998. Recently, while parke outside in a driveway, not running at all, the horn started to blow on it's own. It was a constant blowing, not intermittent. We took the fuse out for the horn. I have to have the horn in working order for
|
| a/c drain | 21 Aug 2005 21:03 GMT | 3 |
does anyone how the a/c drain is routed? is it at the bottom of the evaporator box and can you get to it or see it from the passenger compartment? thanks. I need to try and clean it out.
|
| RS2000 Remote Starter K3500 | 21 Aug 2005 13:57 GMT | 3 |
I installed a RS2000 remote start in my Chevy 1998 K3500 truck with a manual transmission. Haven't been able to get it to work. Tech support emailed and said to call them I have to prime the remote
|
| 4l80-E first or second gear only | 21 Aug 2005 03:36 GMT | 4 |
I recently finished a transplant of a 94 3500 2 wd 454 and 4l80-E into a 90 2500 that had a 4.3 and 400 Trans. all the components were swapped harness, comp, sensors ect . My problem is the Trans didn’t work. 2nd gear only, the Trans was
|
| '02 8.1L Crank Position Sensor | 21 Aug 2005 02:03 GMT | 1 |
The truck: 2002 8.1L 2500HD w/ 30K miles I posted before about this, but think it is pinned down to this sensor for several reasons.
|
| Why do 350 chevy's miss? | 20 Aug 2005 09:48 GMT | 8 |
I have my truck and I need some things to go over to check and see why its missing. I need the most obvious first. Its a rebuild and I am getting some missing. Also How do you set the air/fuel mix? Should I turn it out turn and a half
|
| Fiberlok Console Liner?? | 20 Aug 2005 06:46 GMT | 1 |
I am trying to find a fiberlok console liner, they attach to the top of Chevy/GMC console lids and they prevent things from sliding around, i heard that Performance Products had them, so i called them and they told me they know longer carry them. I sure would like to find one for my ...
|
| Temp sensor? | 20 Aug 2005 01:50 GMT | 5 |
Have a 1998 GMC 1500 with the 5L v8.... Did a bunch of coolent/gasket work on it a few months ago, and managed to snap off the connector to the engine temp sensor, was able to pop it back on and secure wiht a wiretie, worked fine for a while, then had to build up a ball of ...
|
| help plz..Brake lights do not work now | 20 Aug 2005 01:31 GMT | 6 |
2001 Trail Blazer My brake lights have quit working and was wondering if anyone can help me get them to work again. I have checked the fuse and the blubs.
|
| 2003 5.3 Silverado Transmision concern | 19 Aug 2005 23:50 GMT | 2 |
1st gear seems a bit whinny and lack in power. At times it will shift hard between 1st and 2nd and others it shifts fine. The hard shifts seem to occur more fequently when accelerating from a stop letting off the gas some, (1000 to 1500 rpms) then trying to accelerate again.
|
| 95 chevy pickup 1500 4wd not working | 19 Aug 2005 21:50 GMT | 7 |
it has auto trans, when i shift in to 4wd it seems to go in with ease but doesnt work and the linkage seems ok. i dont have locking hubs. could a hub sensor have gone bad or maybe the hubs need to be cleaned.
|