Hello, the vehicle is a 1993 Chevy 1 ton diesel 6.2 (non turbo) with
4L80E electronic overdrive transmission. The last few weeks I heard a
grinding noise each time I started the truck but I thought it was the
starter.

I need to change the rear breaks on my tracker. The drum is stuck. Does
anyone know the size of the bolts for the puller on the drum and the
thread count. Also are they for a puller or to screw in and push off the
drum. Either way I can do it. Also are there any other things I ...

I have a '89 s10 Blazer that has a door window off track.  Any one know
the secret to getting on back on track. (I have new edge clips)

I have had water in my gas tank. To fix the problem I have dropped and
drained the tank, put a new starter on, replaced the spark plugs and
wires,replaced the fuel injectors, fuel meter, air filter, fuel filter,
oil filter, changed the oil, and put gas in.. the truck will NOT start. ...

 I am gonna change to Synthetic Oil.
Do I need to run a cleaner through it?
I talked to a few people and they said since I have low miles,no.
04' 2500 HD 6.0 14,000 miles

I need to change the rear breaks on my tracker. The drum is stuck. Does
anyone know the size of the bolts for the puller on the drum and the
thread count. Also are they for a puller or to screw in and push off the
drum. Either way I can do it. Also are there any other things I ...

What is it wih some people in this group posting there email as
anyoneatanywheredotcom@somthing.com   ?????    Why not just put your email
address in.  I am certified mechanic and I have not responded to alot of
emails because I finr this to be a major pain, when you click reply in

I've been troubleshooting a friends truck.  We completely rebuilt the
top half of the engine.  Rebuilt heads, new cam, new timing chain,
lifters, etc.  It still has an issue with timing.  We tried a new and
swapped back to the old tps, map, iac sensors.  The new ones didn't

My dad has a '91 Chevy with a 350 in it (around 150,000 miles on it), the
intake manifold gasket was recently replaced by a mechanic but shortly after
that the oil pressure dropped to about half that it used to be so we sent in
an oil sample to a lab.  Finally got the results, ...

I have a 2002 S-10 4.3 V6 that needs a oxygen sensor.  Are you supposed to
put any anti-seize compound on the threads prior to installation?

I repaired the broken connection in my wiper circuit board about 2 years
ago. Has worked fine until now.When I turn on my wipers they will not turn
off and will only run on one speed and the washer pump will not spray.This
problem is intermittent Early in the am they work fine  ...

I have a 97 Suburban, the high pressure hose line on the power
steering has been leaking.  I removed the old hose, installed a new
hose, refilled the pump, and now I can't turn the steering wheel.  I
tried removing the new hose and nothing is coming out of the pump,

i got a 81 chevy luv truck. my dad and isaw this web page and it was a
v6 we think it is a 2.8 litter v6 so we wont to put one in it and see if
it works befor i do i was wondering if i could be able to do it that way
e-mail me at this adress cause i am not always in here. so pls ...

Anyone ever use one of these things and if so, do they work? Any
comments good are bad would be appreciated before I buy one.
http://www.autobarn.net/torfuelsav1.html

Can only drive about 1/2 hour then engine gets hot and runs at about 210,
then starts to idle rough, engine starts to knock, then completely stalls
out          I think it is timing chain or fuel pump  
I could use some feedback if you agree or have any other ideas