I know the big trucks are moving slowly these days, but what about the
compacts?  I know I traded in my Sonoma last year and got a couple thousand
more than KBB suggested I would get from the dealer on a trade-in.  Almost
as much as they listed for a private party sale.  Since ...

 I have an 82 GMC S-15, v6 2.8L, 2 wheel drive, long wheelbase.
 After 140,000 or so miles, one of the driveshaft U-joints disintegrated,
and the subsequent flailing around destroyed the equally old driveshaft
support bearing and cushion (it's a 2 piece driveshaft).

Anyone added the parts/equipment to a manual steering vehicle? Is it
fairly strait-forward, or a real pain? This will be on a '93 Nissan
truck, not my Silverado.
Thanks, GC

Need direction to remove and replace water pump for 1996 S-10 Blazer, V6

I've noticed the last winter that when I shift my 92 S10 Blazer into 4 wheel
high, it works great. When I shift it out, the wheels disengage but the
light on the console still shows it is in 4 wheel.  The front wheels do not
spin so that part is not engaged but at higher speeds ...

When I drive over 50mph my 2000 blazer has a vibration.  What could this be?
It hasn't done this in the past.

The vehicle in question is a 1989 Chevrolet S10 pickup, 2WD, 4.3L V6, automatic
overdrive transmission (700R4 I think?), mileage estimated somewhere above 150K
(odometer doesn't work).
A few months ago a problem began to develop where the engine would lose power

The plastic housing around the driver's side door handle has cracked so
that the whole assembly (lock and all) is starting to come out of the
door.  I can still open, close and lock the door, but the handle
definetly needs replacement.  I assume that I only need to replace the

Need some help on the procedure to replace the cruise control switch on the turn signal lever. Will I have to pull the steering wheel and the cover asy or is there some slick procedure that I am not aware of? Any help or advice would be appreciated
TJ
--------------=  Posted using ...

We've had a '93 S-10 Blazer 4.3 4x4 with 4 doors & a front bucket for
many years now & are pretty happy with it.
Outside in the parking lot is an '89 4.3 4x4 with 2 doors & bucket seats
for $1300.

I've read a lot about intake manifold gaskets, and now I am facing the
problem myself.  I just got a rip-off estimate (my opinion) for the
repair of my rig.  Evidently everything went south at the same time
last night driving home.  Within a 1-2 mile stretch of road, my temp

 I have an 1986 chev k10 3" lift truck.. the problem is I took the springs
out, and the bushings are screwed in them These are the front leafs I am
talking about. The front hole of the leaf is like a 22ml bolt the rear a
17ml bolt with 5/8 nut at the shackle.. Where can I buy ...

Heres the deal. I have a 1996 Chevy Silverado 1500 V8 5.7 liter. I took
my truck to AutoZone for their free computer dianostic check because my
check engine light was on. Their computer said I needed to change Bank
1 and Band 2... Sensor 1 on both banks. So I did. While I was at it ...

For the past week, I couldn't get the key out of the ignition on my 96
S10 blazer. I finally removed the tumbler and was able to get my key
out, but when the tumbler is in, it won't release its grip. The tumbler
looks ok, and the tumblers fall/rise correctly with it out of the

Truck:  1996 Yukon 2dr 4x4
I just finished towing a trailer, and now my brake lights no longer
work normally.  The third roof mounted brake light works fine, and I
when I press the brake pedal I can hear the switch or relay under the