| Thread | Last Post | Replies |
|
| 1995 S-1o Fuel Injector/ Running Rough | 09 Jan 2006 05:36 GMT | 5 |
I just replaced a fuel injector in a 2.2l s10 . Now , I have a miss at low speeds . and Idle . Anyone experience this.
|
| Turn Signal (Blinker) & Headlight Problem | 09 Jan 2006 01:17 GMT | 4 |
I'm looking for some help diagnosing a problem with the turn signals and headlights that I'm having. I have a '91 Chevy Silverado 1/2 ton pickup (5.7L) 210K mi. that gives me problems with the turn signals. Conditions are as follows:
|
| 96 Silverado 4x4 : Major turn signal problem | 09 Jan 2006 01:15 GMT | 5 |
This is strange, 1st symptom : odometer light was intermittent then about a week later. Left turn signal will not blink when the head lights are off.
|
| tailgate stuck question | 09 Jan 2006 00:18 GMT | 2 |
Hello - The tailgate on my 2000 Silverado Z-71 flareside is stuck shut. I have a spray in bedliner and cannot see if there are any screws on inside. Outside is a trim piece around handle. That came off once and was repaired with double sticky tape. . I do not remember any screw ...
|
| 90 Sierra Won't Start | 08 Jan 2006 22:48 GMT | 3 |
1990 GMC Sierra won't start. All electrical appears good except nothing happens when you turn the key . Battery has been checked out (even replaced with another new battery) but no luck. Idiot lights come on on dash, but not even a click from the starter. Lights, radio, turn ...
|
| Hot Malibu | 08 Jan 2006 19:29 GMT | 2 |
1995 3.1 some times runs hot,the tempgoes up and down,heater blows hot air then cold.put in new manifold gasket.still does same thing.its like theirs an air pocket in it.tried bleeding air from radiator.changed waterpump,themastate.any ideas what im missing? thanks.
|
| crank pulley on 250 L6 | 08 Jan 2006 17:59 GMT | 8 |
I have a 72 C-10 Fleetside and it has a 250 in it. I cant figure out how the pulley stays on the crankshaft. I see no bolt and its not a press fit. Does the belt alignment hold it on during operation? stumped in Va.
|
| GasCapCaddy.com | 08 Jan 2006 14:39 GMT | 20 |
I have been bothered for a long time by the gas cap hanging down against my paint, whenever I put gas in the car. It's put too many scratches/scuffs in my paint. I thought about removing the leesh, but I don't want to lose my gas cap.
|
| '98 'Burb: Aftermarket Photochromic Side Mirrors? | 08 Jan 2006 13:00 GMT | 1 |
The inside center mirror on this thing automagically adapts to bright light - like photochromic sunglasses. I like it a lot. Having the driver's side outside mirror do the same thing would be great. Any chance of finding something?
|
| Cannot Get Truck to Run Hot... | 08 Jan 2006 01:43 GMT | 16 |
96 Chevrolet 1500 V6 I have already posted this to rec.autos.tech but eventually could not get a resolution over there, so I am hoping you guys can help me out. My truck runs too cool. Here is how it works:
|
| gas mileage-2003 suburban | 07 Jan 2006 22:59 GMT | 6 |
I've asked you guys/gals this before-- but now that I've had my 2003 for 4 months-- I wanted to ask again. At best-- I'm getting 14 mpg-- average 12. Is that about right?
|
| How to Remove Driver's Side Interior Door Panel to replace handle | 07 Jan 2006 22:52 GMT | 1 |
My husband bought a new handle for his '97 Chevy 4X4 (I think it's a Silverado? Z71?) and doesn't know how to get the door panel off to even start the attempt of replacing the handle. He DID buy the handle though! Any tips would be greatly appreciated.
|
| how to get the wipers off s10 1989 | 07 Jan 2006 22:43 GMT | 5 |
I posted, a few weeks back , a question as to how to get the wipers off a 1989 s10 ; the answer is: you pry them off; I used a screw driver on one, and the claw of a hammer on the other; they are held on by splines on the shaft base; the
|
| Getting more milage per gal. | 07 Jan 2006 17:50 GMT | 24 |
I just bought a 2001 Chevy 2500 with 8.1 Engine I wonder is there any I can do to get better gas mileage other than putting in a smaller engine? PS: Getting a little power won"t hurt thanks Tim.
|
| Engine block heater wiring ....(2004 2500HD-gas) | 07 Jan 2006 12:55 GMT | 1 |
Hi: Anybody know the correct wiring placement for my block heater cord in my truck ? This is the gas (6.0L). I've unfastened the wire loom from the frame rail and wish to know how I proceed with accessing and storing the wiring between connections....Also, when does this gas
|