I have a 98 Chevy Silverado Z71,it has a 350 vortec.My manual says to
tighten valves until there is no play left,then turn one whole turn and it
should be set.This is setting each cylinder seperate.I did this and it will
not start.What is the correct setting for this motor?

Hi all...
I've got just about everything needed to get my '86 K5 up and running
after a fire took out a portion of the wiring harness and distributor.
Just a couple more small pieces and I'll be back in business.

Truck as described above.
Parked truck on day, wouldn't start the next.
Replaced ignition coil, plugs, wires, and module located on distributor
plus module located on the firewall. Still wouldn't start.

I've noticed with my 2000 blazer (bought 7/2005) that when in 4WD and I turn
a tight corner, I feel a resistence, like the wheels dont want to turn.  I
have also felt this when backing up into a parking spot in 4.
Thoughts?

I have a 1998 4x4 Chevy V6 (a 4.3 I think).
It misses when crusing about 1500 RPM and above, also when
you accelerate. It also loses power if you floor it all the way.
This only happens when:

Have a 198 Chevy 4x4 with 350 and automatic.  Snap On Solus unit shows code
300 - random missfires on cylinders 3,5 & 7.  Replaced plugs wires and have
had fuel injection cleaning performed by dealer - motor is now periodically
hard to start - but not always - and blubbers just ...

What is it about top posting that some people get in a huff about? I don't
come across many people that have a problem with it, and I always top post,
and I am not the only one, but there aren't many. To me, its easier to read
someone's reply when it on top than to run all the way ...

Hello everyone. My 1993 GMC G3500 van's backup/reverse lights won't come on.
I've checked the fuse, the wiring (as best I could), and replaced the bulbs.
I'm at a loss. The only thing I can think of is a backup sensor or switch.
Where is the backup sensor or backup light switch on ...

I'm looking for some advice with regards to purchasing an 80s model Chev
short box pick up or full size Jimmy.  My question is whether or not I
should buy an 87 - 91 model with early fuel injection or not worry and save
some money and get a slightly older one with a carb.?  I ...

Hello i have replaced my tail light assembly three times.  Each with a brand
new replacement assembly.  The brake/turn signal socket keeps getting burnt
then the whole assembly is bad because of one socket.  I used some
dielectric greese on the socket and this still happens.  The ...

I need to find a way to get the signal coming out of my brake light
switch going to the brake lights to install the brake actuator for my
trailer and I can see the wires and brake light switch above the
steering column but I"ll be dammed if I can work on them up there.

does any body know how you are supposed to bleed the air out of the cooling
system of my 5.7 liter 1993 cheyy silverado 4x4.Do I just open cap with the
heater on or is there more?
also it has a slight miss is this a comman thing that can be fixed in the

I have a problem with my 96 GMC.  Thought I would check to see if any
of you guys had any answers.  I was driving my truck last night and all
of the sudden it started acting as if it was starving for gas.  I had
just turned into a neighborhood and my rpms were low.  I stepped on the

I ordered a bunch of brake parts for the truck.  The parts never came.
I can't get in touch with a real person.  Won't respond to emails.
Got ripped off.  Time for a credit card dispute.  Hopefully this will
save some of you the same hassle

A couple years ago I bought a used blazer 89k miles then.  A two weeks
later I end up have my transmission rebuild by the Chevy dealer, which
was not cheap.  I had to pay for it myself, since it was sold as is.
Now, my car has 130K and it started making louder noises while ...