| Thread | Last Post | Replies |
|
| Door Adjustment/Alignment 2001 GMC Jimmy. | 16 Apr 2006 01:32 GMT | 1 |
How do I adjust the front drivers door. It seems the bottom pin thru the hinge has too much play allowing the door to drop approx 1/2 inch when not latched. Is there a bushing or something around the pin where it meets the
|
| Door Adjustment/Alignment 2001 GMC Jimmy. | 15 Apr 2006 21:42 GMT | 1 |
How do I adjust the front drivers door. It seems the bottom pin thru the hinge has too much play allowing the door to drop approx 1/2 inch when not latched. Is there a bushing or something around the pin where it meets the hinge?
|
| V6 Diesel | 15 Apr 2006 17:42 GMT | 15 |
Any chance of a 1/2 ton with a V6 diesel some time in the future??
|
| Transfer case mount and bushing allowable play | 15 Apr 2006 07:10 GMT | 7 |
I have an 86 3/4 ton 4x4 that vibrates when you reach 55 mph. I have replaced the u joints (there are just 2 on the rear shaft) which did quiet it down some.... but the vibration/drone remain. I have noticed that when I push up on the drive shaft near the xfer case the mount below ...
|
| 92 s10 v6 blazer that will not start | 15 Apr 2006 06:18 GMT | 7 |
When trying to start this 92 s10 v6 chevy blazer it will turn over 1 time, but will not start and then when turning the ignition to try again there is a loud clunk sound. It will not turn over. My mechanic says that he didn't put it on a machine but it keeps locking up and he ...
|
| 90 S10 blazer won't start | 15 Apr 2006 06:04 GMT | 12 |
I've got a 90 S10 Blazer that will start run for 5 to 10 seconds and die. It will finally start and stay running as long as I don't shut it off, if I do everything starts all over and it can take 5 to 10 tries to get it going. So far I've changed , cap, rotor, plugs, fuel pump,
|
| radio programing | 15 Apr 2006 04:23 GMT | 1 |
i bought my Chevy S-10 around 2 years ago and i see the locked word on the radio. I talked to the previous owner and he gave me the code for radio and i was wondering if anybody would know what to do from there? JJ Kibs
|
| ZR2 opinions needed | 15 Apr 2006 02:57 GMT | 1 |
thinking of getting a 1999-2002 ZR2. are these fairly reliable & is there something special i should be checking for when i look at some? thanks......
|
| Help! | 15 Apr 2006 01:22 GMT | 2 |
I am having problems with my 86 Chevy Silverado 2wd pk-up. The problem is that the starter won't crank. When I turn on the key, I can hear clicking noise, but when I try to start it there is nothing. I did the head light check test, the lights do not dim when I try to turn it over. ...
|
| locating brake switch in 88 chev | 14 Apr 2006 16:27 GMT | 1 |
After reading about people with much the same problem, I was wondering if someone could tell me where to find the "brake switch" in this truck. Sounds as if it is the culprit. Thanks in advance.
|
| 96 Surburban 1500 4x4 Radiator woes | 14 Apr 2006 05:00 GMT | 4 |
Can these be repaired if the tanks start leaking? I'm not positive the Plastic tanks can be resealed to the core. What is the best route to take as far as buying a new one? AutoZone etc or any online wholesalers etc? Thanks ...
|
| drl | 14 Apr 2006 00:57 GMT | 2 |
hi i cant get my drl lights to work on my chev silverado 99mod i`ve checked the relay in the fuse box in the engine room and it seems fine. in the wiring diagram there seem
|
| 91 chevy | 13 Apr 2006 22:48 GMT | 1 |
This truck still will not start. It now has a new pickup coil, control modual, coil, cap & rotor, computer, ignition switch. I have been through a haynes manual with a multimeter and can't find a thing. It still will not get fire at all, plus now it appears it is not getting fuel. ...
|
| 98 Blazer-Will not go into 4 Wheel Low | 13 Apr 2006 21:25 GMT | 8 |
I have a 98 Blazer with the electronic 4 wheel drive selector. When I select 4hi, it switches with no problem. When I select 4low, the light flashes for about 20 seconds and then goes out. I assume that there is a soleniod somewhere that is stuck, but haven't
|
| Do I need hub centric or lug centric wheels? | 13 Apr 2006 14:37 GMT | 2 |
Ordering some new wheels tomorrow. They offer a hub centric version and also a lug centric version. Do I need to order hub centric wheels for my truck? It is a 1996 GMC Sierra 1500 Z71 that came with the 16 X 7 inch, 6 bolt
|