I have a 98 chevy 1/2 ton.  I have the 9.5 inch 14 bolt rearend.  I was
wondering which other vehicles would have this same one.  My pinion
bearing went out which in turn ruined every gear inside the case and I
thought it would be easier to just replace the entire axle assembly

Hi...
Recently, during some random reading done out of boredom, I became
aware of the 292ci I6 engine that was available in Chevy full-size
trucks back in the day.  It appears that even the K5 Blazers were

I have 1996 1500 V8. I'm sole owner and an old man.  I do believe I'm still
burning .95 cents a gollon gas. About every 4/5 weeks I drive it to the local
Safeway, only because my wife is driving the other vehicle.  It has about
25000 miles on it now because when I first got it I was ...

I am frustrated to say the least.  In the last year I have replaced:
The battery, alternator, water pump, and fuel pump all at different
times and due to different reasons.  I just put in the fuel pump last
week as it started to act up and then this morning yet another

After not using my beast for a few months-winter, I had to replace a corroded
dist.  Ever since, when driving, acceleration is fine, idle fine, but when
backing off acceleration and maintaining speed, it bucks and backfires like
it's running out of gas.  Then I'll put my foot back ...

I am trying to replace a badly decomposed steering wheel. Stripped out one
of the bolt hole s while trying to remove the weheel. I plan to resort to a
gear puller, but would like some wisdom on this. Could use some help.
I am too poor to pay some one to do it. I am trying to get ...

Can anyone provide directions on how to remove the armrest from an 01
Yukon SLT (w/ leather)? I'm talking about the armrest attached to the
front seat.
Thanks in advance

is it at all possible for an alarm system to make the parking light/tail
lights not work for any reason on a 97 silverado?
reason i ask is i got an alarm put on my truck like a month ago and all the
fuses are good yet i haven't checked the bulbs but i doubt that it the case

Any recommendations or advice which is better: Chilton vs. Haynes?  I'm
not very mechanical but am looking to learn more about basic
maintenance/repairs and would like to know what might be better suited
for me?  Any advice is appreciated.

Looking for information on the Piston-to-Bore clearance of the 6.6L
Duramax.  This is information that should be in the shop manual (if I
had access to one).  Need to know the clearance spec. and if there is
more than one piston grade.  Thx.

What are the fuel pressure specs for a 96 S10 Blazer 4.3 CPI injection ???? My trucks acting up like
it's running out of gas but it's got 50 psi at an idle, filters new.....  I don't have a manual for
it either.....  
Thanks

Are wheel seals a problem on these trucks?  Have noticed lubricant splashed
along side of the truck.  Was advised that this is coming from the wheels.
First told that the dealer would give me cleaner for it, however, when
suggesting a broken seal might be the problem........make a ...

My Astro spun out and hit a guardrail on the right front and rear corners
and has been totaled. It is an LT with 8-passenger seating, dual air and
133k miles. It still runs great and EVERYTHING works mechanically except the
rear doors. I drove it home after the accident and it still ...

We have an '03 Chevy 2500HD with the duramax and allison transmission. My question is, when pulling in the mountains with tow haul on and one presses on the go pedal, isn't one supposed to get a steady increase in power? When I mashed the go pedal, my truck did not move on up the ...

I just picked up a used Blazer LS 2000 model.  The power seat (driver
side) does not move.  What is th elikely problem???  SImply I get no
response when I try to move the seat by pressing the power button no
matter what direction I want it to go.  What would it cost to repair