This morning on the way to work I started to hear this sound... and at
first I thought it may have been a squeaking belt or something... then
it progressively became worse and I believe it is on the passenger side
rear of the vehicle.

for a good laugh, take a look at "oldechrysler" and "oldiechrysler"
orignal posts on this group, a few weeks back- it was DESERTBOB asking
questions about an overheating problem on his POS ' 86 Chrysler.
He had a stuck thermostat- yet he disassembled the ENTIRE ENGINE

Is there a handy online guide to see which transmissions go in which
models?    I have a buddy who is investigating using a Sprite automatic
to replace a leaky seal Caravan automatic.   I did not think that they
matched, but he thinks they do.

Hi...
Wonder if anyone happens to know, or if not possibly someone
else with a 94 lhs would at their convenience do a little
experiment for me...

I have a problem with my fresh built 727. Its an 83 lock up model
from a Jeep grand wagoneer. Currrently in a cj7 with 258 in front and
d300 behind, 4.56 gears. Trans was built with new high qaulity overhaul
kit; clutches, steels, seals, pump set, 5:1 band lever, a properly

I test drove one and loved it but it had no owners manual and the "L" shaped
series of buttons in the center of the dash kept blinking.  I think they
were the buttons for the rear wiper and washer etc.  Whatever buttons are
just to the left and below the sliding dual temperature ...

I have a 92 Ram 250 , OD transmission went south while comming north on
the NJ turnpike. I have a 91 Ram 250 with a good 3speed non OD trans.
What do I have to change to put the 3speed in the 92 other than the
Trans& I assume the torque converter. All input is appreciated. ANY ONE

Looking for options for a DBR2 scan tool. I know these units were made
my OTC. Can you get a generic OTC unit and upgrade/add-on to made it
DBR2 compliant? I need to be able to "talk" to the ABS computers on
Dodge RAM pickups.

New to the group and wanted to see if anyone had any answers to a
couple of problems i have on my 2001MY Voyager...
Problem #1:  Front end rattling.  When driving over anything but
completely smooth roads (we do have a couple of miles like this in

I have three Chrysler T&C vans 1997, 2001, 2002 with mileages of
225,000 63,000 and 85,000 miles on them respectively. We've owned the
97 and 02 since new and the 01 for three months and about 12,000 miles.
All three are making a grinding feel with some noise when you come to a

Does anybody know if someone makes a cap or adaptor that could be used
to seal the core of the high side service port? I have a 96 Plymouth
Grand Voyager 3.3L with front and rear air. the AC isn't working very
good so while checking it out I noticed the high side port was

Just changed the brake fluid in several cars, including my PT Cruiser and 04
Chrysler mini-van. Every vehicle required a metric wrench to loosen the
caliper bleed screw until I got to the mini-van. Yep, good old SAE English
wrench called for (even though the caliper bolts are ...

I am looking for any information on the best proceedure on replacing the
timing belt and water pump on a 1991 chrysler lebaron convertable, 3.0 v6
with a/c
thank you

I've always been partial to the station wagon.  Mine hauls like a truck,
handles like a sports model, gets decent gas mileage and looks great.  So,
why don't they make them anymore?

http://en.wikipedia.org/wiki/List_of_automobile_manufacturers#World_Motor_Vehicl
e_Production_by_Manufacturer
I'd say that GM is a LONG LONG way from being "tits up"
They surpass Toyota by 35% in production
http://en.wikipedia ...