| Thread | Last Post | Replies |
|
| '00 Durango power lock actuator-HELP | 04 Jan 2005 14:28 GMT | 6 |
What's with these? Is it common for them to break? I need help, it sounds like something has stripped like gear teeth spinning on my drivers side. I tried to get to it but after removing 2 screws at the bottom of the door panel, one large near the arm rest and 1 near the r.v ...
|
| 2003 Dodge Ram 1500 2wd Service Time | 04 Jan 2005 01:59 GMT | 2 |
I have a 2003 Dodge Ram 1500 Reg Cab 2wd truck. I have owned it for about 2 years now, and I am coming up on 33,000 miles. I change the oil every 3000 miles. Its coming up on some stuff listed in the manual that isn't in a normal service of every 3000 miles. I believe the manual ...
|
| Help Again - Ram Wagon 02 | 03 Jan 2005 23:50 GMT | 1 |
Happy New Year everyone! I need some help because i'm not sure what is going on if anything at my local Dodge dealer..... anyway, took 02 Ram Wagon 3500 in for work back in November - bought it used in October wtih 38,000 miles on it - well in November had the bearings replaced
|
| Engine mileage | 03 Jan 2005 23:17 GMT | 4 |
Please forgive if this is wrong group. I'm looking at buying a 1997 Plymouth Grand Voyager with a 3.0 liter V6. It has about 100,000 miles on it. Is this too much for this (Dodge?) engine? Any experience on how long on average they last? Also, any mpg info would
|
| 2003 Ram 1500 vibration Update | 03 Jan 2005 20:37 GMT | 5 |
Interestingly, the dealer called and said that it is probably the engine crankshaft. They are going to scope it next week. Will either rebuild or replace engine. Advice as to any concerns this may causse?
|
| BG Product "44K" | 03 Jan 2005 16:36 GMT | 4 |
I found it a little "weird" that Dodge would, without consulting me first, pour this product into my gas tank at the aforementioned 30k service. The only reason I know about it is that there was a little yellow card included with my receipt telling me so, after the fact. The card ...
|
| What is this part? | 03 Jan 2005 06:24 GMT | 6 |
I '95 3500 van, 318, stopped blowing fuses and starting melting wires yesterday. so I followed the melting toi a little rubber 'box' that mounts with three terminals to the top of the alternator... have no idea what it is. Two little wires that are the right color to be fuel ...
|
| Happy New Year!!!!!!! | 03 Jan 2005 06:20 GMT | 6 |
You folks have a safe and happy one. Roy
|
| 1990 Doge Dakota will not go into overdrive | 03 Jan 2005 00:52 GMT | 1 |
If any one can give me suggestions to the possible cause please let me know. E-mail mcsalkey@nbnet.nb.ca
|
| More diesel weirdness- 04 | 02 Jan 2005 17:18 GMT | 3 |
Has anybody had this happen....I started up my 04 and went about doing some chores while it warmed up. When I came back, the doors were locked. Fortunately I had another set of keys available. I just assumed that I hit the lock by mistake when I shut the door. I drove about 100 ...
|
| Mounting XM or Sirius Antenna | 02 Jan 2005 07:30 GMT | 19 |
I've picked up an XM satellite receiver for the truck and am wondering if anyone has come up with a good way of mounting the antenna on the roof. I'm not so much concerned about the antenna seeing as how it has a strong magnetic base, but I would like to somehow hide the wire.
|
| Silly question | 02 Jan 2005 04:27 GMT | 4 |
I just picked up a new company provided Caravan and cannot figure out how to unlock the side doors from the outside. There are no keyholes that I can find. Anyone familiar with this? TIA
|
| Durango doorlocks | 01 Jan 2005 20:43 GMT | 1 |
Hello everyone!Well I made the plunge and bought an '02 Durango. Everything works fine exept the electronic doorlocks unlock continually without any button pushing on the door units or the key fob happening.This happens mostly when it is raining (or has been raining).My wife talked ...
|
| Where to attach engine hoist on '85 360 V8? | 01 Jan 2005 18:31 GMT | 5 |
My 16-YO son and I are in the middle of rebuilding the 360 engine on my '85 Ram (long story, which I won't go into here). We tore most of the engine down with it still installed in the truck; then we discovered that the crankshaft needed to be machined. So we pulled the block. ...
|