| Thread | Last Post | Replies |
|
| Where does the a/c clutch ground? | 27 Aug 2004 22:45 GMT | 2 |
My son's 96 F150 a/c wont engage. There is power to the clutch but not a ground. I traced it through a pressure switch than it disappears into the harness. There is a relay in the fuse box that keeps cycling when the a/c or blower is on, Probably has something in common with the ...
|
| ''98 Ranger Fuel Filter | 27 Aug 2004 20:16 GMT | 3 |
All; My 98 Ranger, 4 cyl, 2.5L, fuel filter seems to be installed in a way that I am not familiar with. How do you get the damn thing off?
|
| '93 Full Size Bronco A/C Question | 27 Aug 2004 18:47 GMT | 3 |
This might be a silly question, but, does anyone know if I can replace my original A/C blower motor with one that provides greater volume? The original blower works as designed, just not enough volume to cool the entire vehicle as quickly as I'd like.
|
| Billitt accessories for Ranger | 25 Aug 2004 19:44 GMT | 1 |
I just bought a 04 Ranger XLT and i am trying to find a place to get Billitt aluminum accessories for my interior. I would like to replace the AC/Heater control knobs, and especially the very small radio knob.
|
| Bronco questions | 25 Aug 2004 05:16 GMT | 4 |
I have been offered a 1989 Bronco. I haven't seen it yet, and I don't know much about these vehicles. I'll probably buy it anyway, but I wonder if anyone here could help me out. 1) Are the 1989 Bronco 5.0 liter engines fuel injected? All? Some?
|
| help! What is this? 93 F150 question 5.0L | 25 Aug 2004 03:17 GMT | 1 |
On the front passenger side, just behind and below the battery is a plastic rectangular box which hangs vertically. It has two plastic removeable caps and two hose fittings (or did) and two hoses hanging near it (not connected and one seem to be broken off the thing) one
|
| Ford F250 1990 error codes | 25 Aug 2004 02:41 GMT | 6 |
Hi for my neighbour I'm looking for a way to read the error codes. We have no oil pressure according the gauge but the engine runs fine :), but we want to be sure, we have a warning light going (engine) and can't pull the codes. (don't know how) or find the oil pressure sensor so ...
|
| Ranger 1989 shift boot | 24 Aug 2004 06:46 GMT | 4 |
Does anyone know a good souce for aftermarket shifter boots.....the one in my ranger is all ripped up....I checked JC Whitneys catalogs and didnt see anything that would fit......Thanks
|
| Stupid transfer case question | 23 Aug 2004 09:51 GMT | 3 |
Can anyone tell me the difference between a "divorced" and a "married" transfer case? There's one of each locally at a geat price. But the guy thats selling it doesn't know the difference either. Thanks
|
| Ford Ranger Super Cab | 23 Aug 2004 01:46 GMT | 3 |
Hi, we own a 1999 Ford Ranger Super cab. We like the vehicle but when it rains it scares us to death. It feels like we are losing control the vehicle if we go over 25 MPH in the rain. The tires looks good so I don't think it is the traction. Is there anything we can do to make
|
| Ford Ranger Power Steering | 22 Aug 2004 12:43 GMT | 1 |
I have a '97 Ranger that had a power steering leak. Took it in to a non-dealer service station that replaced the lines. When I went to drive it away it was as if there were no power steering at all so I stopped and the service guy came out and he couldn't figure out why it didn't ...
|
| Bronco - fuel Inj to Carb conversion | 22 Aug 2004 04:57 GMT | 8 |
I've got a 1986 bronco with a 2.9 engine, I'd like to convert from a fuel injection system to a Carburetor. Anybody have any advice? Like what parts I need for this, Manifold - Carb and such. I've searched the web and found nothing of use.
|
| v8 trannys and v6 trannies interchangeable? | 21 Aug 2004 22:36 GMT | 2 |
Have a real nice '80 F150, 300 six, aluminum OD tranny. I swapped an iron case (T98?) into one of these years ago, but forgot-will a tranny from a v8 fit the six? Thanks,
|
| '98 front license plate | 21 Aug 2004 07:40 GMT | 2 |
Does anyone know how I could remove the metal rivets that hold the front license plate in place? I've tried drilling it out with a hand drill and i've ruined a few bits already. thanks!
|
| headlight conversion question | 21 Aug 2004 03:08 GMT | 4 |
I want to put old-type headlights in a 97 Ranger. I know, that might sound crazy here but I had Hella E-code cases in my last car, a 90 VW Fox and liked them. I used Sylvania xtra vision bulbs, 55/60w and fed them using a Painless 30815 harness with relays built right into it
|