| Thread | Last Post | Replies |
|
| F250 Warning Lights / Siren | 23 Nov 2004 19:16 GMT | 1 |
Folks, I need to install Warning Lights and a Siren on a 2003 F250 SuperCab. Anyone here running a set up, can you share your ideas? Example; Light, Make, Style, Location and where did the wires run into the Cab?
|
| FBI turned AMERICA into a NATION of PROGRAMMED SLAVES and ROBOTS | 22 Nov 2004 03:58 GMT | 7 |
Please save this column on your computers and email accounts and also forward this to all your friends, family, coworkers, democracy websites, civil liberties websites and as many americans as possible who are genuinely concerned about CIVIL LIBERTIES and FREEDOM in
|
| 95 bronco ABS ring removal | 22 Nov 2004 02:10 GMT | 2 |
found i have 3.55's, got the rotor/hub off, loosened the lugs. Any help getting the abs rotor off, looks like thats my only prob. Rotor will not rmove without removing the abs rotor. Thanks in advance.
|
| Noise in transmision? | 21 Nov 2004 23:39 GMT | 1 |
-------------------------------------------------------------------------- I bought a F150 super crew 2003 from a dealer (just 15000 miles on it). This is a Ford certifyed vehicle and I also got the extended warranty on it, just in case.
|
| Any Rusted Oil Pans? | 21 Nov 2004 23:30 GMT | 1 |
I replaced the rusted oil pan on my 1993 F-150 4.9L (2Wd 5-spd) myself. It took 4 hours but probably a pro could do it in 2. My repair manual (starts with an H) listed extra steps like: remove the radiator, remove upper plenum, and remove starter.
|
| Help me decide on which gauges for my F-550 PSD | 21 Nov 2004 21:20 GMT | 8 |
I have been looking at recommendations for which gauges are the most needed while towing a trailer. I am towing a 17,000# fifth wheel with my 2000 F-550 PSD 4.88 rear. The rear differential has full synthetic (I understand this bumps up the F-550 GCWR to 30,000#).
|
| Rear Main Seal | 20 Nov 2004 05:11 GMT | 10 |
'95 Bronco, XLT, 351ci, 4X4: Am I too ambitious to tackle this myself? I have the tools and a lift, any idea what steps can I can 'skipped' in the Chilton's Manual and how long it would take someone who is modestly equipped with experience?
|
| 2004 ranger dash light | 19 Nov 2004 01:08 GMT | 7 |
BlankI drive a company 2004 Ranger with a cap. At about 5,000 miles the dash lights stopped working. Since I only drove it in the daytime I waited for the 30,000 mile maintenance to get it fixed. The dealer fixed the problem last week and the lights worked for five seconds. I ...
|
| High Rev When Clutch Depressed | 18 Nov 2004 14:50 GMT | 3 |
When the clutch is depressed, engine revs to about 4000. Any ideas?
|
| Outside Temp. Gauge | 18 Nov 2004 02:23 GMT | 1 |
I have a 2001 F 150 Supercrew and the outside temp. keeps reading 140 all the time. Could this be a bad sensor? If so where is it located and what does it look like. Thanks
|
| Battery not charging | 17 Nov 2004 08:03 GMT | 16 |
I have a 1981 F 150 with good alternator, new voltage regulator and still it isn't charging the battery. Anyone with any ideas.
|
| Power window motor replace | 16 Nov 2004 18:22 GMT | 2 |
how difficult is it to replace the power window motor on a 1988 Ford F-150 pickup ? anyone know where I can find step by step instructions ?? --
|
| Blown sparkplugs | 16 Nov 2004 16:12 GMT | 2 |
Anyone have the engine model or serial numbers of the Ford engines that are blowing out the spark plugs? near as I can tell it is from 1998 to 2003 models of the V-8 and V-10.There should be some way to get this information without pulling the plugs and measuring the threads.If I ...
|
| 54 f150 | 16 Nov 2004 13:38 GMT | 1 |
need any info on this truck, especailly color availability, color of engine components, wheel tire combos etc. Interior colors seat styles and options. Have one in good shape but as i work on it would like to bring it back to original.
|
| Tie rod ends | 16 Nov 2004 06:26 GMT | 1 |
Hello: I have my '01 F250 4x4 and noticed that the grease cups on my tie rod ends are ruptured. Is there any way to replace these without replacing the tie rod ends? I would hope you could pop themm apart and put a new cup in there and just pop them back together, thus saving a ...
|