Hi Guys, I have an '87 Ford e-350 with 2 air pumps, no thermactor and no
catalytic converter.
The belt broke on the air pumps. Nothing else affected. Is it ok to drive it
back home so my young friend can fix it? I'm an old Guy. LOL

Hey, I AM THE VICTIM, of a hit and run, I was in the store for  long
time,and when I came out the damage to my truck was done,I have a
witness,who gave me the plate nmber,  but the local police really wont
do anything because these people are from another county,with no

Does anyone know how hard this is to do?
Chad

I have a 2000 excursion with a 7.3 power diesel engine.  Can I use dyed, or
red diesel fuel in it without ruining the engine?
Thanks,
Steve

04 F-250/350/450/550 Superduty Econoline, Excursion SR 110 TorqShift
Transmission issue
Got my notice from Ford to take my 04 F-350 to the shop for Customer
Satisfaction Program 04B24.

I would like to put a set of factory Ford van bucket seats in my 79 F150,
but I cannot find any seat brackets that work. I have tried a set from a
1978 Bronco, no luck. I have also tried a set from a 1988 Extended cab 4X4,
and again, they will not work. Any suggestions?

Trying to replace the old blown out stock speakers.
i see 1 screw on the panel but after that nothing, do i just yank really
hard on it?
anyone else done this before?

I bought a used 1985 E350 25' motor home.  A few people said these usually
came with 4.10 ratio but mine has 3.54 (door sticker 53 code, big 7400 lb
capacity).  I got good power now (460 with hi perf exhaust and intake) but
worried I might cook the tranny if I tow a bass boat or a ...

Hi, I need to replace my front bumper ,and lower valance-due to a hit
and run. I need a black metal bumper, with the lower half that dark grey
plastic ,with the factory lights. I have a 1999 ranger. I have been
searching and havnt came up with much luck. Any informaton would be

Hi
I need help with some info for mateing up a 1965 289 with a 1979 ford
C6 trans.
 I put the flywheel and converter on the 289 that came off the 302

I bought my 2001 F150 with only one key, and it's got one of those
immobilizer chips. To make a dupe, one needs 2 keys, and so I'm fixing up to
make a visit at a dealer's. Dealer's time is expensive, and so I got blanks
off the internet, and am going to pre-cut them, leaving only ...

Can anyone advise as to what my problem may be? I have a 4ltr 4X4 stick
shift ranger from 1999. Its got about 80k miles on it.
I sometimes feel under hard acceleration as if the truck tries to turn left
using its rear wheels. Then I let off the gas it feels like it straightens

I need to remove the bucket seats from a 2002 Ranger.  The bolt is a
star head.  I have a #55 socket but it is too small and a #60 is too
large.  Three auto parts stores and the local hardware store says
there is nothing in between.  Anyone with some helpful ideas?

I just got a 2000 motorhome on a 1999 Ford chassis with the V10 engine and
just found out that they tend to blow the spark plugs right out of the head
at about 20k miles because there are not enough threads holding the plugs
in.

I have an 83 351W (83 - 93 one piece real main seal) that I was hoping to
put in an older (69 -72) pickup or mustang.  It came out of a Bronco, and
most of the early 80's 351's were put in Vans, trucks, LTDs and Crown Vics.
Will this engine bolt into a earlier Ford truck or ...