| Thread | Last Post | Replies |
|
| 01 Ranger A/C failure | 24 Jul 2006 23:15 GMT | 8 |
I have an 01 w/2.3L DOHC 4cyl. Over the last few years the A/C died a slow death in terms of producing cold air. I didn't bother doing anything about it as I don't use it much anyway. But now, with temps > 100F and high humidity, I'm wondering what the likely cause is. A/C doesn't ...
|
| 7.3L Ford Startup idling | 24 Jul 2006 04:15 GMT | 4 |
I recently changed the fuel filter and the air filter in my truck. I have also recently changed the oil&filter along with the transmission oil and filter. I did the fuel and air filters this past week and had no problems what so ever. Today when I started my truck up after
|
| Plug Gap | 24 Jul 2006 02:16 GMT | 3 |
I'm trying to find the correct plug gap on my 91 Ford E53 460 engine. Book says "check the vehicle emissions sticker" in the engine compartment. No sticker there. It's a California Chassis. Can anyone help. I recall the gap is wide, but how wide?
|
| F350 7.3L diesel bleeding question | 23 Jul 2006 22:29 GMT | 8 |
I have a 93 F350 with the 7.3 diesel engine, and am ready to change out the coolant. I have read that after draining the block and radiator of antifreeze, you need to bleed the system while refilling it. The instructions I read say that while filling, you need to disconnect the
|
| 88 F150 Manual cutting off while driving | 23 Jul 2006 00:42 GMT | 1 |
Hi: I have an F150 Manual Trans that I replaced the starter and solenoid on several weeks ago which seem to be working fine but since then I occasionally had trouble with the truck missing 2-3 times while driving down the road after about 10 minutes. It kept going but the
|
| Premium sound question in 2003 Explorer | 22 Jul 2006 23:27 GMT | 3 |
I have "Premium sound" in a 2003 Explorer (In-dash 6 cd player). Is there an auxillary input, or can one be added? Thanks in advance, David
|
| EEC-IV code | 22 Jul 2006 21:17 GMT | 4 |
----------hi.... I have got fault code on my car. 1992 E150 302 EFI V8 . The codes are 172,327 and 328. Can anyone please help?
|
| 89 F150 Ignition timing Problem | 22 Jul 2006 15:25 GMT | 21 |
Here is a recap of a previous closed message: Ford F150 won't start May 25 2006 Truck was driving fine when muffler exploded and truck did not start again
|
| Vibrations 1994 f150 4x4 | 22 Jul 2006 03:45 GMT | 18 |
I have a 1994 F150 4x4 with vibrations once I reach 30 mph. I replaced the u-joints and no help. replaced the front hubs from automatic ones to the manual locking ones. I am not sure what else could be the problem with it. Any help would be awesome.
|
| 1994 F 150 4.9 timing information wanted | 22 Jul 2006 02:00 GMT | 7 |
I've got a 1993 F150 with a 4.9 inline 6 and I';m curious about the timing. When I look at it with a timing light its above the 12 degree mark and when I advance the throttle, it goes up a little then stays at the 12
|
| 91 Ranger XLT 3.0L v6 EFI Code 22 BUT Ford says NO MAP sensor | 21 Jul 2006 20:30 GMT | 1 |
So far nobody has an explanation for this one. The "check engine" light on my 91 Ranger came on some time back. The truck did not run any different after the light came on than it did before the light.
|
| 6.5L diesel surge on low fuel | 21 Jul 2006 14:30 GMT | 6 |
Had an odd thing happen today. Crusing along at 70mph and fuel tank is close to empty but not quite, and suddenly I get a surge of power that felt like a turbo kicking in (not a turbo vehicle), and it went up to 80mph without moving the pedal. Then as suddenly as it happened it
|
| IRCM Location on a '92 Bronco | 21 Jul 2006 02:12 GMT | 2 |
Does anyone know the location of the Integrated Relay Control Module (IRCM) on a 1992 Bronco, 5.8l, 4x4? Also, a description of what it looks like would also be appreciated. Thanks - HH
|
| Gas Gauge Lamp on Ford Ranger | 20 Jul 2006 10:00 GMT | 5 |
I was looking for an answer on this and basically copied and pasted somebody else's question. Although I didn't see an answer. Does anybody have one? On my '97 Ranger XLT, the lamp behind the gas gauge is burnt out. Not a
|
| Mice Elimination | 20 Jul 2006 07:51 GMT | 3 |
A quick question. Has anyone figured out a great method for keeping mice out of engines? They seem to love my E350; they build comfortable large nests right in the middle of the intake manifold of the V10; they then proceed to eat the vacuum lines.
|