| Thread | Last Post | Replies |
|
| Removing Ford Aspire Motor | 04 Sep 2006 05:53 GMT | 1 |
I need to remove engine on a 1996 Ford Aspire. Can this be removed without removing trans with it. Please say yes, so I wont have to remove those axles. thanks
|
| Ford 3.9 ECT | 04 Sep 2006 05:40 GMT | 1 |
Does anyone know where the coolant temperature sensor is on the 3.9 liter engine in a 2000 LS. I believe this is the AJ30 engine. I have been told under the intake, on the radiator, back of the head, oil filter housing.... all by dealers!
|
| Diagnose loss of power 93 Escort | 04 Sep 2006 05:28 GMT | 12 |
Hi, I was driving down the freeway yesterday ( a hot day), and after about 5-10 minutes, I lost 90% engine power. The car did not die though, I was able to limp to the side. A couple hours later (after I had it towed), it started and ran fine....
|
| sources for 67 Ranchero parts... | 04 Sep 2006 00:53 GMT | 5 |
Hi - looking for an alternate source of parts besides autokrafters.com - they have "most" of the stuff we need, but things like a replacement gas tank is not available through them. Please post any sources you have that have been able to fill the gaps.
|
| Ford Festiva Screaching? BRAKE? | 03 Sep 2006 21:36 GMT | 1 |
Festiva screaching? I have a 1993 Ford Festiva. Everyday when I leave to go to work, at the first 2 stop signs there is a screaching sound when I use the brakes. Then there isn't any noise after that until I come home. But not as much as
|
| Air Senser? | 03 Sep 2006 21:13 GMT | 5 |
Just replaced my air box, due to cracking and leaking in dirty air. with a cone air filter...works and sounds good but one problem, there was one senser that was in the box that obviously isnt on the cone filter (its not the mass flow senser) its a little one. So i kept the
|
| 98 contour tranny | 03 Sep 2006 19:44 GMT | 8 |
98 contour 2.5 auto. Please help. tranny is pushing fluid out of the dipstick tube. Seems to get worse when turned off.Thanks Greg
|
| '04 Super Cab w/ Under 20k - Front Brakes Squealing Badly | 03 Sep 2006 15:29 GMT | 7 |
I bought this truck new and I have about 19.4k miles on it. A few weeks ago the front brakes have started squealing badly. I looked at the rotors this morning and they look like they are getting very scored.
|
| '95 Crown Vic front end | 03 Sep 2006 15:14 GMT | 2 |
I need to replace the idler arm and one tie rod near it - anyone done this on one of these? I haven't worked on a recirculating ball system in a few hundred years. Thanks!
|
| bad ignition coil pack? | 03 Sep 2006 05:53 GMT | 3 |
I finally got my 93 Ford Escort to crank but not start. It is getting gas. I just bought and put in new plugs and wires. The engine was still cranking but not starting. We pulled out all of the wires and tested them and they were getting a spark except for the first plug
|
| 1992 Sable rough idle after 1 minute | 02 Sep 2006 21:18 GMT | 3 |
A family member has a problem with a '92 Sable (3.8L) after about 1 minute after startup (hot or cold engine). The engine starts to idle rough, and sometimes stalls. Restart is fine and acceleration is good with no problems. The car has 76K miles and had a head gasket
|
| 2006 ranger | 02 Sep 2006 20:02 GMT | 4 |
could someone with a 4cyl 5 speed tell me how there mpg is?
|
| 94 Crown Vic Erratic Steering | 02 Sep 2006 17:30 GMT | 6 |
The tires are fine, the alignment is fine, the fluid level is fine. Car won't steer straight, goes back and forth left and right, the steering is still power (not hard as if there is no power steering). The steering is totally treacherous and is extremely
|
| Snow tire rims | 02 Sep 2006 12:10 GMT | 1 |
I have 2003 Mustang with 16" alum. wheels. Would like to get 15" steel rims. For snow tires. Can someone tell me what would fit. I called couple of wreckers they said they don't have anything.
|
| automotive restoration project software? | 02 Sep 2006 04:34 GMT | 17 |
Anyone have any good recommendations for software to track automotive restoration projects? Or, a web site that has a data base to track all the bits, pieces, money and vendors relating to a car's restoration? Not too worried about cost if it is good software or a good site.
|