| Thread | Last Post | Replies |
|
| fiesta zetec 1.25 1997 r acceleration problems | 08 Sep 2006 18:04 GMT | 1 |
i have a problem(obvious really!), with the accelerator pedal fully depressed the car will get to 3500-4000 and its like someone applies the handbrake, if i keep it on a light throttle it will rev past this nearly to the limiter. also the revs "hang up" when the clutch pedal is
|
| FORD WINSTAR YEAR 2000 | 08 Sep 2006 17:17 GMT | 7 |
I am having some type of Electrical problem. My dash lights went out the electric windows dont work, and now the speedometer doesn't work, I checked the fuses seem to be all working. Is there possibly a Relay gone bad, I am not a mechanic, the only test equip I have is a fuse tester ...
|
| 1990 GT A/C Idle Problem | 08 Sep 2006 07:48 GMT | 5 |
I have a 1990 GT and when I turn on the A/C it makes the car idle much lower than it should be...i have been told that this is some sort of part that is supposed to increase the idle when the a/c is switched on but i haven't been able to confirm where it is; the car will even idle
|
| puttin'a F/INJ.302 in 66 mustang help!!!! | 08 Sep 2006 03:14 GMT | 2 |
was on the fence here. need some advice before i purchase the motor and "brain". (eng.managment computer) Is the harness and the brain all i will need? out of a 95' says it's a "boss".
|
| 1966 ford id? | 08 Sep 2006 01:30 GMT | 6 |
I work in an auto salvage yard, and we just got in a 66 ford. I am going to buy it, just wondered if anyone could tell me anything about it. Title only says 66 ford 2 door, no model on it. VIN is 6u67c171504 The only badge on the car says LTD, though several people have looked at
|
| Will New CEO Alan Mulally develop a Ford Flying Car? | 08 Sep 2006 01:06 GMT | 3 |
Being the former head of Boeing's commercial aircraft division, Mr. Mulally is in the perfect position to proceed with the long due perfection of the flying automobile which so many of us have longed for. Not only that, but there is no limit to how far he can improve the ...
|
| WTB. Ford 9 Inch Rearend. | 07 Sep 2006 14:44 GMT | 5 |
Need Ford 9 Inch rearend for race car. Near Wisconsin. Tom
|
| 96 Ranger clutch problem | 07 Sep 2006 05:41 GMT | 2 |
96 Ranger 4 cyl, original owner 25K miles. I have an internittent problem with the clutch. It works fine most of the time, but now and then the clutch pedal doesn't want to depress. Seems to happen when truck is driven more than 30-40 miles.
|
| Ford cancel minivans | 07 Sep 2006 00:55 GMT | 1 |
Ford will stop making minivan early 2007. Transmission for these van will stop being produced in oct 2006 Another crap van too Adiso Ford
|
| scorpìo '87 | 06 Sep 2006 23:02 GMT | 1 |
yelow (or orange) brakes light is blinking, at startup key, about 30seconds ¿do you know why? ¿low level fluid? the bottle is over full at stop engine
|
| 2000 Mystique | 06 Sep 2006 21:50 GMT | 1 |
2000 Mercury Mystique 2.5L Duratec V-6, CD4E Automatic. PROBLEM - intermittent misfire of cylinder #4 (according to codes read at local shop). Seems to cold start with no hint of the roughness, but when driving after
|
| 87 F150 300 6 cyl bucking & stalling on highway | 06 Sep 2006 12:23 GMT | 10 |
Recently bought the truck mentioned in the subject line. After about 10 miles of highway driving it started bucking and finally stalled. I managed to roll to the shoulder out of traffic. After about five minutes wondering what the problem could be I tried starting it again,
|
| 1948 F6 Wheels | 06 Sep 2006 05:08 GMT | 1 |
I have what I believe to be a 1948 Ford F6. It started out as a fire pumper and somewhere along the way was converted to a rack body truck. The wheels are split rim 5 hole design ( I believe they are 20 inch) and have rusted through, exposing the backing for the tubes. Since ...
|
| possible starter problem??? Please help | 06 Sep 2006 04:59 GMT | 1 |
I need a little help. I have a 1989 Ford Mustang LX with a 2.3 liter engine. I had to change the torque converter and after I finished, it started fined but then cut off and will not restart. I was told that transmission fluid (it was everywhere) could have gotten into the ...
|
| Master cylinder issue | 06 Sep 2006 04:15 GMT | 1 |
I am installing disc brakes on my 1966 Galaxie and during the process, I must have pushed the brake peddle down with the rear brake lines attached and the front brake lines not attached. The master cylinder is working the rear brakes but not the front. How do I "re-set" (for ...
|