somebody mentioned something in an earlier post about using a different carb
on a YJ. Can you do that in Kalifornia???

I know TJ fuel gauge accuracy is less than perfect, but I have a
problem with my gauge lately where it works about half of the time and
shows E half of the time. When it fails, usually turning the jeep off
and back on will fix it. It either works OK or not at all. Yesterday

i dont really know where to begin to explain the sequence of events that
took place over the past couple of weeks. it started with picking up a uhaul
truck in fayetteville, nc and returning it in fayetteville, nc some 14 days
later.

Hi guys,
I am in the process of installing a Detroit TrueTrac in my rear axle
D35C. (I'm a bit in over my head, but there is a first time for
everything:)  and I have a few questions maybe some of you can help me

I have a 2000 Jeep Wrangler 4.0L sport.  I have 32" tires and no lift.  I am
planning on towing a 4x6 or 5x8 uhaul trailer from Las Vegas to Iowa in a
few weeks.  I know I need new rotors and am wondering which ones are the
best to buy.  I have been looking around and have ...

how can i remove the shifter off the tranny? i'm getting ready to take the
body off the frame and don't really want to drop the tranny first.  i was
hoping to keep the tranny on the frame and just remove the body over it.  i
haven't figured out how the shifter comes out.  is it ...

Hey Everyone,
 I thought my '82 Scrambler was turning incredibly high revs on the factory
tach, but a friend gave me something to think about.  Since a V8 was swapped
into it (401 before, i'm putting in a 360) the factory 6 cyl tach is probably

I have a 88' Jeep cherokee and the crank windows in the front drivers
and passangers side doors continue to ruin my speakers. Orginally when
I bought the the cherokee it had sony 5 1/4" speakers in it, but one
was trashed and about a month later the other one broke too. I pulled

Do the 2004 TJ's manual transmissions have the same marble rattling noise
that the 2000 TJ's had/have when in  neutral? Or is this the same 5 speed
manual transmission with the same noise.
Thanks,

There are a lot of fabed parts out on the market that are shipped unpainted
and am curious how well rattle can type painting works on them. Poison
Spyder has some really nice stuff but none of it comes painted. Another
company is AtoZ Fabrications. I was thinking of maybe using a ...

My 1964 CJ5 has a 1/2" -5/8" diameter x approx. 6" long sheet metal tube
attached vertically to the outside of each of the rear corners.  These
appear to be original to the jeep.
Does anyone know what the intended use is for these?

Any tricks for bleeding ABS?
I installed new callipers, bled and topped up the reservoir. I'm getting a
steady stream from the bleeder but the pedal goes to the floor with the
engine running. I can pump the brakes for a little pressure but it goes to

Friend is trading in her 97 for a new car.  It has 50K on it and has been
meticulously maintained.  I think I can get it for 6K.  It's got the 4.0 and
an AT.  I have a suspicion these may be a maintenance nightmare.  The
warrantee is running out and maybe she knows this.  Any ...

"Jeff,"  I know what you are doing when you are writing your troll posts or
reading one of our replies.  You might want to read the following before you
do much more of it though.
http://www.stopmasturbatingwithjes.us/

Apparently the RAMJW newsgroup has a charter.  I'm sure something in it
covers hostility and foul language.  As some have said, families may be
reading this stuff.
Anyway to get someone kicked off for blatant breaking of the rules?  Of