I am examining my lift kit and comparing the u-bolts with my stock ones.
The kit U-Bolts are about a half an inch wider than my stock ones so they
are not as snug as the stock ones.  They do not "hug" the axle.  Will this
work or should I use the stock ones (if they're long enough).

 Curious if anybody's put this engine/tranny in a Jeep and/or comments or
considerations.  I'd like to keep my Dana 300.  TIA.
                                o_o_o_o
 Best Regards,      /| ,[_____],

I've got a 00 XJ Sport with AC.  It's way too cold here and yesterday I
tried turning the HVAC selection knob to the recirculate setting on the
AC side (9 o'clock on the dial).  I found that as long as the temp
setting is on hot i get hot air.  Does anybody see a problem with ...

I really like the Line-X in my Jeep and am getting ready to have the same
put in my M-416.  Has anyone had this done?  Any problems with the drain
plugs afterwards?
The trailer is also going into the shop for a spring over so I can put 35"

I'm considering the Turbo City Adjustable Timing Sensor for my '97 TJ
I'm interested in the installation details of this item. Is is just a
bolt on replacement or is some sort of detailed adjustment necessary?
From the photograph that I have seen, it looks to me this there is

Anyone have pictures of a nerf bar bolted to a CJ frame? I installed a set
of new ones on my 2001 Ranger and of course it bolted up to existing holes
in the frame. Are there holes in the CJ frame for this?? It's too damn cold
for me to trek out to my jeep tonight. And IF I have to ...

I have a 1999 Grand Cherokee with 33,000 easy miles on it.  Bought it new.
It is out of the three year warranty now.   I have had the front rotors
either resurfaced or replaced 5 times by the dealer,  for warping out of
specs. and causing a distinct wobble and/or pulsation.  I just ...

I was wondering how they would eventually announce this kind of news
with minimal effects.
http://biz.yahoo.com/bizwk/040116/b3867094mz063_1.html
BusinessWeek Online

Sad news...  This guy just moved to Michigan and was staying in a hotel.  He
said he stayed up till midnight watching it snow up to 3' (and watching his
Rubi in the parking lot).  When he got up this morning, the Rubi is gone!
He had about $15,000 dollars of bolt on mods. (wheels, ...

My right front shock mount broke off my jeep the other day.  Only one bolt
hole is damaged.  The other two are fine.  I called the dealer for this part
and they want 66.00 for it and the local parts stores can not get it.  Does
anyone know where I can find this part at a more ...

Hello, I need to replace the neutral safety switch on my Jeep. I have
the new one and the Chilton's says it's on the transmission but I
can't find it. Maybe I have the wrong one... The one I have is a Borg
Warner # S9185. It is about 1.75 inches long, has a place for a 3

Hello Jeep Lovers!
I just want to share my story. I have 1997 Jeep Grand Cherokee. Two days ago
I decided to change shocks and bought Monroe Reflex. From first kilometer I
was like in ocean storm - all 4 wheels shaked, wheel shaked it was drive

I have a 97 GC with 90k. and one day the information center (where date and
time is) started to blink. Now whenever I start the car it gets reset and
blinks. The fuses are fine. Any ideas??
TIA,

There are two questions here.    I have a   1980  CJ-5, with V-8 engine. I
cannot say when the plugs were last changed  (years), and I think that the
plug wires are original.     I plan to change the plugs and wires soon.  Is
there a very good specific brand to use for this?    I ...

86 Cherokee 2.5 fuel injection just started idling rough.
What are my candidates to check out?
If I accelerate it smooths out... and sometimes it will smooth out at idle,
but it's rough idling most of the time.