I just looked at the 4.0L valve cover which will be going on my 4.2/4.0
combo and I noticed the PCV valve was clogged with gook (on the inside of
the valve cover are three screws which allow the PCV casing to come away
from the valve exposing the PCV Valve itself).  Can the valve:

Good morning. Well, I posted here a few weeks ago with an unknown issue
that I thought might be the transmission. It was diagnosed by those here
and a tranny shop as other issues. At the recommendation of the shop, I
replaced cap/rotor, I had just done plugs and wires and skipped ...

hey guys-here's a quick one-is the shaft on a saginaw steering box
tapered? the one where the pitman arm goes on.  i didn't get a chance
to look at mine this morning.  can one install the pitman arm upside
down? thanks! 85 cj7 with power steering....

anyone know what is going on with their website? haven't had a chance to
give them a call but i can't access anything pass the main screen for each
section.....

A couple weeks ago when the temperature was about 25 Farenheit,  I
kicked on my ARB lockers.  After I finished up off-road,  I unlocked
the differential,  but forgot to turn off the power to the compressor.
I got onto the freeway, differential still unlocked, and about 15

I've been reading: A History of the Korean War: Pusan to Chosin. Anyway, in the
organizational chart for the US Army of that day they mention a Pioneer &
Ammunition company, which is normally attached to the headquarters company of
an infantry battalion of the US Army. What does a ...

I'm installing some new axle joints on my D30 and had trouble getting the
correct axle joints (u-joints?).  The first set was to small on the caps and
I had to return them (after wasting a day waiting for a ride) to try and get
the correct size.  I took the old joint to Napa and ...

I am in the UK and have just bought a brand new Liberty (2.8 CRD) (called
the Cherokee over here, but I have no idea why!!).  I love it!
Anyway I am thinking of having side steps/running boards put on.  I am a
little hesitant as I know of someone who put side steps on a landrover ...

Hello..
I do not have a local jeep dealer close by and I was wondering
if anyone knew of a good place to order parts. I need a new A/C
clutch for my 97 TJ...

not really a technical question but I thought I would see what the rest of
you Jeepers do in the summer months with your soft top ?  Let me explain my
confusion.. please excuse my Newbie-ness.
This is my first summer with my 03 Rubi.  It was 80 degrees friday. I took

Leaf springs appear very worn; worse on the front where it appears to
be dropped a couple of inches on each side. Very noticeable.  (These
springs are barely more than flat.)
Just got new tires and alignment at my long-time favorite alignment

Any body tried doing anything about these dumb ultra-high front seat-backs
that block your view when you try to back up or look out the right rear
window? They're also too damn low.
The seats in my '99 were perfect. Why does Chrysler insist on changing

I removed my rear seat belt retractors to install a tire carrier that
required me to temporarily remove the retractors.  The driver side retractor
has taken up all the loose belt and I can not pull the belt out to reinstall
the retractor into the roll bar.  What do I do to release ...

Thanks again for the welcome back. I'm having some problems with my MOPAR
fuel injection on my 258. It runs great once it's warmed up but upon first
start in the morning it runs like crap. (not sure how crap really runs but
its the best familyish word I can come up with right now.)

Any suggestions on how to get it off?  It's on a Jeep, so at least
it's relevant to this group:)
Thanks in advance.
Will