Well look like my problem with my abs is the passenger TONE WHEEL. Mechanic
said he had to replace the whole axle, Some theet on the TONE WHEEL are
completely gone. Can anyone tell me if the parts imself can be replace ? or
i really need to replace the axle ?

My current beater is a 90 XJ 5spd 4.0 with 3.07 gears (D35/D30), 31" tires.
One of my part XJ has the same axles as the beater with the exception of
4.10 gears.  Could I swap the gearing over to the XJ with 3.07?  All I am
looking for is a little more gearing.  If this thing makes ...

I have a few things i would like to replace on my 94 Grand Cherokee but
i would like to find the best price and place to order from.    Thanks
for the help

Went from 3.08 to 4.56 (based on suggestion from this group) on the TJ.  Now
running 3K RPM at 75 mph, a little high to suit me. Plenty of power in 5th
gear!  Probably go with 35's when I ware out the 33's... should be just
right then!  (The question in the back of my mind now: ...

Where can I get info, articles, etc, about replacing the old 4.2 with the
newer 4.0L H.O.?
I am planning on doing this on my 89 YJ..
Does anyone have a good complete 4.0 H.0. for sale, somewhere near ontario,

Looking for a Jeep CJ in or around Texas. Prefer '80 or early years,
but open to all leads.
I have a Suzuki Bandit Motorcycle as well as a AR-15 w/extras to trade
+ lil $

I took the plunge and am picking up my '03 TJ Sport tomorrow night!! Biggest
difference between it and the '97 I used to have is I'll have the 4.0L and a
hard top. Don't know what I'll do in the summer yet - I'll be too broke for
a while to spring for a soft top. Maybe a bikini ...

How difficult is it to replace or repack front wheel bearings on a
2000 wrangler sport, 6 cyl?
TIA
Joe Carroll

this is from a longtime member of another forum i frequent...  his 16 yr. old
daughter ran away - was a girl without any previous problems or history of
doing such...
http://www.rx7club.com/showthread.php?t=353823&page=1&pp=15

  Wondering about swapping a early eighties AMC Eagle 258 motor into a
76 CJ5 that has a 232 in it. Does it go right in or are adapters needed?
  Ed Huesers
  http://www.grandshelters.com

I'm looking at a 78 CJ7 all original, 304 with Quadratrac. I'm not real
familiar with the quadratrac is it reliable and tough? Or should I steer
clear and stick with the danas and t-176, t18 etc. Also with the 78 -the 304
is not as de-tuned as later models -right?

Does anyone have a link or the specs for a '79 Jeep 360, from a J20? I need
to know the RPM at peak torque, peak torque, RPM at peak HP & peak HP. I am
trying to select a torque converter for my junk.
I am not sure of how to adjust the curve for a Holley ProJection, I might

Hey everyone i have a 97 jeep wrangler that has had a 10" rockford sub
in the rear for less than a year.  The sub blew so i purchased an
infinity reference 12" sub.  I ordered a 12" truck box from ebay but
it turns out that the box is too thin for the sub an the sub hits the

We have a '93 ZJ with V-8.  The Jeep is 12 years old with 90,000
miles.  A couple of years ago it started to have a roughness that
comes and goes.  I have eliminated tires and balance as a source.
Also the motor mounts have been replaced.  Now I am looking at the

I'm going to build jeep m38 fiberglass replika and i'm looking for drawings
of body (with dimensions or scale).Here in Poland there is lack of such
documentation, plastic scale models etc...
Body-model is rather simple to build, but I need dimentions ... :)