| Thread | Last Post | Replies |
|
| Need Pressed Ally Number Plates - Any Ideas? | 16 Sep 2004 18:45 GMT | 13 |
I'm after a set of pressed Ally number plates, ally on black, for my SIIa rebuild project. Anyone know any online suppliers? Cheers Alex
|
| Freelander rear wndow | 16 Sep 2004 18:42 GMT | 8 |
On our Freelander, if you open the rear window, to say half open, and stop it, and then try and close it a fracton, it does not close a bit but opens all the way. You seem to have to close it all the way shut and then open it again and try
|
| Series SNORKEL | 16 Sep 2004 14:22 GMT | 1 |
K ive got all the bits i need for my snorkel on my S3 88 Question is what to do with the oil bath air filter.. Cant put the pipe into the top as it wil touch the bonnet underside.. If i make a hole in the side itll have to be welded to the centre pipe in
|
| Clear Indicators | 16 Sep 2004 13:32 GMT | 9 |
Does anyone know where I can get a clear set of indicators for my TD5 90 , I saw them on one of the lighting stalls at the LRE Show. They were about 7 quid each (but they only had one) and I have lost the details of the shop now :-(
|
| power steering | 16 Sep 2004 06:48 GMT | 5 |
I have had my 93 range rover about six months with no steering problems. However after being away two weeks the steering is very heavy when slowly going around corners but still seems okay on the motorway. Is this a co-incidence with the vehicle being unused for two
|
| 110 Bad earth - where to look | 16 Sep 2004 00:22 GMT | 1 |
I have a 93 110 CSW which seems to have a bad earth, but I am not sure where to look. When I press the brake pedal (and brake lights come on), the fuel gauge drops to empty. Anyone have any ideas/experience with this.
|
| Weld or replace? | 15 Sep 2004 22:39 GMT | 5 |
Recently bought a 1989 90TD who's chassis has seen better days. It requires fairly substantial welding (about 5 evenings worth) which a friend said he would do for ?200, but after this I will still have a 15 yo patched up chassis, which will be fine, but another friend says he can ...
|
| Squeaky Brakes on Freelander | 15 Sep 2004 20:26 GMT | 5 |
We have a '98 Freelander whose front brakes squeak, mainly in dry weather conditions. The squeak is a continuous 'singing' which is worse when the front wheels are turned, and eases up when the wheels are straightened up again.
|
| Bearing rumble on Series III | 15 Sep 2004 20:15 GMT | 22 |
I have a Series III which has developed loud bearing rumble on overrun. and I'd like to lay the symptoms before the group. I shall have to get it fixed... I may have been pushing my luck getting home.
|
| Series 2a dash panel terminals | 15 Sep 2004 19:50 GMT | 17 |
Top left of the centre dash panel on Series 2a, there are two small sockets, one with a red surround and one with black surround. I'm assuming that they are a remote 12v supply and earth, but what are they for?
|
| LRO Peterborough | 15 Sep 2004 17:10 GMT | 52 |
Off first thing tomorrow morning. Anyone know of any hassles getting in with a club / trade pass on wednesday (Simon???) If there is, please expect to see a purple 101 parked in any nearby
|
| brakes. it's not that, so what is it? | 15 Sep 2004 10:14 GMT | 16 |
OK, I have managed now to properly adjust the brake shoes on the back of my 110. However when I actually use the brakes the symptoms are just the same (needs a couple of presses of the pedal to get the rear brakes to play
|
| N reg Defender 90 with ECU? | 15 Sep 2004 09:56 GMT | 3 |
I've just bought a N reg Defender 90 (not sure if its 95/96 or 200/300tdi) and it has under the middle seat a Diesel EGR, ECU with the following # ERR 6233 Type 4115. It has a landrover logo on it. What does this unit do?
|
| Free Wheeling Hubs OUCH! | 15 Sep 2004 08:41 GMT | 5 |
Checking all the wheels today i noticed movement on the front wheel. So decided to have a look (Wish i never bothered). Looked in the haynes manual and calculated the hub nut might want tightening. Problem How the hell do you get the Fairy freewheeling hubs off. Undid the
|
| Autobox Question | 15 Sep 2004 00:29 GMT | 13 |
Piglet won't change down, and changing up seems to be delayed. Apart from the obvious fluid check, is there anything it might be? I can't check the level as I;ve waited for it to go cold...and now it's dark!?! EP90 leak in t/fer is quite bad, could this have an impact? Kickdown ...
|