Car Forum - Land Rover Cars

Thread preview

Thread	Last Post	Replies

Piston replacement	11 Dec 2006 19:42 GMT	6
1987 90 2.5 petrol 1. Can one replace the pistons/rings from underneath or does one have to take the head off too? (again!) 2. Can one get to the camshaft chain tensioner to fix/replace it without
more Youtube	11 Dec 2006 19:27 GMT	9
http://www.youtube.com/watch?v=78yAUckdgxA&mode=related&search= like the choice of music. ooh, this one looks fun: http://www.youtube.com/watch?v=Yd864pr_5Ng&mode=related&search=
Ho Ho HO MERRY CHRISTMAS!!!	11 Dec 2006 18:06 GMT	14
Right then! Seasons greetings to one and all! Hope Santa Fills yer sack with Swivel grease ;-) ... and come on all you Lurkers out there, lets be hearing it from ya!
Please help. Cannot find a part	11 Dec 2006 10:14 GMT	4
I wonder if anyone can help. I need to find the following part: "Half moon bell housing cover for LT95 gearbox" My local 4x4 place was very very helpful and tried three different covers, but none of them fit properly. May be you guys know someone
rodders you dipstick!!	11 Dec 2006 00:23 GMT	4
Checked the oil level this morning on the 200tdi, and the tube came out with the dipstick... Ive pushed it back in again, but it gone in too far as the oil level is about half an inch over where it should be.
Gear Change Problems - sorted	10 Dec 2006 18:08 GMT	1
In an earlier post Marc Draper suggested: "Remove the gear lever complete with the alloy turret that holds the large pivot and you will find the bush that the small ball on the bottom
Nice bit of Camel Troph action.	10 Dec 2006 09:24 GMT	6
1989 Amazon car wash exteme :-) http://www.youtube.com/watch?v=r91CtE6xHQ8&NR Makes you feel all warm inside :-) Lee D
more Youtube	10 Dec 2006 08:28 GMT	3
teehee: http://www.youtube.com/watch?v=cCPCyJrC3ZQ&mode=related&search= Signature Austin Shackles. www.ddol-las.net my opinions are just that
101 noise on overrun & other flibbity gibbets	10 Dec 2006 07:16 GMT	25
Anything over 50mph ish if i lift my foot i can hear a grumble type noise, there is no grumble type noise on acceleration. I know Lee did the front diff ages ago. I still dont feel the engine's running right either, i got one pop in
ignition timing RRC 1988	09 Dec 2006 21:04 GMT	3
Hello group, I have a 1988 RRC (VIN SALLHAML4EA 333910) 3.5 Efi Auto with engine # 25D127045. The only problems I have is that I cannot find a definitive answer to the question what the correct ignition timing is for this engine (0° ± 1 or 6° ± 1) and if it is OK to run it on 95 ...
Series 2 - new front axle?	09 Dec 2006 18:59 GMT	1
Brought Stig home today (Series 2, 88"). He goes well with the new engine, but the front axle is very noisy. Swivels are rough, frankly, and the front axle as a whole looks like it could be the one it left the factory with 49 years ago.
cross ply tyres	09 Dec 2006 16:50 GMT	6
I have an odd pair, Firestone 7.50x16 LT and Goodyear 7.50x16 c, of 6ply cross plies with lots of tread. The Michelin 7.50 R 16 XCLs that my 110 was demobbed with have done a further 80k kms and are looking a bit low.
lr no plates	09 Dec 2006 16:13 GMT	2
Blatant plug for no plates http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&ih=001&sspagename=STRK%3AMESE%3A IT&viewitem=&item=110065479141&rd=1&rd=1 Signature Please include ALL previous emails with reply
Landy to the rescue!!	09 Dec 2006 16:00 GMT	4
http://www.youtube.com/watch?v=qMJBKTmDYuA&mode=related&search In the Daintree, Tropical Queensland, Orstraylya
Disco 300 TDi immobiliser	09 Dec 2006 15:54 GMT	3
How do you find out if it's got one? I've just been asked if ours has, and while I assume not (M 95 model) it occurs to me that actually, it could have - unless it went wrong, how would I know?