| Thread | Last Post | Replies |
|
| 91 Maxima lost signals | 07 May 2006 12:42 GMT | 1 |
My 91 Maxima seems to have lost the signals. The only thing that seem to
work is the light that turns on while signaling next to the headlight (when
the headlights are on). The bulbs seem to be fine so I'm thinking it might
be the signal switch on the steering column however ...
|
| Service questions | 06 May 2006 17:29 GMT | 3 |
1995 Maxima GXE, Automatic, 217,000 KM.
1. Need new brake pads, do I go for Nissan pads or aftermarket, if so, what
brand.
2. Dealer says to change Transmission Fluid and also to wash it. $200.00
|
| FRONT HEADLAMPS | 05 May 2006 21:10 GMT | 4 |
i was wondering what i should use to get off a cloudy film thats on the
front of my headlamps yellowish in color.. Please let me know what i
should use with out damaging them?
|
| Does my ECU need reprogramming? | 04 May 2006 17:01 GMT | 2 |
After I got SES light, I disconnected the battery (both cables), and that resetted the light. But now I seem to get poor fuel economy (72 miles for a quarter of the tank). Do I need to reprogram ECU, or the cause is just the way I drive? (No speeding, freeway driving
--
KillerBee
|
| 1999 Infiniti i30t tail light lens cover replacement | 04 May 2006 12:58 GMT | 1 |
I brought my car in to get the rear spoiler repainted, now I find a 3/4 inch chip in the corner of my right rear tail light assembly. I brought the car back to the shop and asked the owner if it could happen there, he said that his guys are very good at owning up to breaking ...
|
| Is $500 too much to replace EVAP canister and vent control valve? | 03 May 2006 00:36 GMT | 2 |
I have a 1998 Maxima GLE with 112K miles. My 'Check Engine Soon' light
came on recently, and when I took it to the Nissan dealer, it was
advised that I had to have the EVAP Canister and Vent Control Valve
replaced, as well as the Knock Sensor. Each repair would cost $500.
|
| Pulled the Codes P0138/P0139 From Maxima 2000 | 02 May 2006 18:09 GMT | 5 |
The list says it's OC2 sensor (both of the codes). How hard it is to change, and how much is it? Could it be not tighten gas cap or anything simple like that
--
KillerBee
-----------------------------------------------------------------------
|
| 2002 Maxima SE 6 Spd -RPM while shifting question | 02 May 2006 15:36 GMT | 3 |
I have searched this group and Maxima.org forums for a definitive
answer...
I've been driving manual shift cars since I learned to drive, but this
is my 1st "performance" 6 speed...
|
| ABS light ON - Possible problem is - ? TIA | 02 May 2006 09:53 GMT | 1 |
|
| maxima | 01 May 2006 11:25 GMT | 1 |
firing order for 89 maxima v6 3000
|
| 90 Maxima timing | 01 May 2006 11:20 GMT | 3 |
I have set the marking as shown in the chilton repair manual. It
engine was running, but the left bank was at 125psi and the right was
at 150psi. This made the engine make a lot of back firing noise. I
was trying to fix this, but after making the adjustment to the timing
|
| new axels cause car not to move | 01 May 2006 08:24 GMT | 4 |
Hi, i got new axels a few weeks ago and the day after i got them i was
driving from sd to phoenix and the car just stopped. do you think its
the new axles, or maybe the transmission?
|
Sign In
Join
My Latest Posts
My Monitored Threads
My Blog
My Photo Gallery
My Profile
My Homepage
Start New Thread